Quartier Notre-Dame Route de Cavaillon CS 10047 84122 PERTUIS cedex (France) Tel : +33(0)4 90 09 47 00 Fax : +33(0)4 90 09 64 09 E-mail : [email protected] www.pellenc.com ENG Translation of the original user guide USER GUIDE CONTENTS: • Cleanion sweeper • Rotary brush READ THE USER GUIDE CAREFULLY BEFORE USING THE MACHINE

TABLE OF CO NTE NTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 GENERAL SAFETY INSTRUCTIONS FOR THE TOOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 SAFETY MEASURES ASSOCIATED WITH CHARGER AND BATTERY USE . . . . . . . . . ....

Dear Customer, Thank you for buying the Cleanion sweeper. When correctly used and maintained, this tool will provide you with years of satisfaction. ENVIRONMENTAL PROTECTION Your equipment comprises numerous materials which can be valorised or recycled. Entrust these to your reseller or to an approved service centre so that they can be processed. Comply with the regulations in force in your country as concerns environmental protection associated with your activity. PLEASE SAVE THESE INSTRUCTIONS This manual contains important information and operating instructions for the following tool: the...

CAUTION Read all the safety measures and all the instructions. Retain all the safety measures and instructions for later reading. This device is not intended for use by anyone (including children) with reduced physical, sensory or mental capabilities, nor by anyone lacking in experience or knowledge, except if they are supervised or have received prior instructions from a person responsible for their safety. • The Cleanon sweeper is a professional tool whose use is reserved exclusively for interior or exterior cleaning of roadways, industrial sites, tourist or private areas. The sweeper removes...

SAFETY INSTRUCTIONS Maintenance and Storage a. Make sure all nuts, bolts and screws are kept tight to be sure that the equipment is in good operating condition. b. Replace worn or damaged parts so that the machine remains safe. Only use original spare parts and accessories. SAFETY MEASURES ASSOCIATED WITH CHARGER AND BATTERY USE Please refer to the battery instructions of the relevant Pellenc tools.

Your sweeper should be used with caution. With this in mind, pictograms to remind you of the main precautions to be taken have been included on the ejection flap of the machine. Their meaning is explained below

DESCRIPTION AND TECHNICAL CHARACTERISTICS

2- Magnetized control unit 4- Handlebar adjustment knobs 5- Handlebar clamping screw 6- Handlebar height adjustment knob 7- Battery protection cover 13- Support wheel steering knob 14- Level adjustment knob 15- Working pressure adjustment knobs 17- Right reverse button 19- Sweeper direction button 21- Left reverse button 23- Brush direction switch 26- Pellenc ULIB 700 or 1100 battery 27- Battery power supply cable 28- Coupling latch holding cord 29- Rotary brush power cable TECHNICAL CHARACTERISTICS PROTECTION OF WORKERS AGAINST THE RISKS OF EXPOSURE TO VIBRATIONS Determination of the hand /arm...

TOOL PREPARATION Your sweeper is currently disconnected from its tool, which was configured in transport mode. The handlebar (3) is folded forwards and locked in place by the handlebar adjustment knobs (4). Follow the start-up instructions below to begin to use your sweeper. UNFOLDING THE DRIVING ELEMENT - Turn the handlebar adjustment knobs (4) to unlock the handlebar (3). --handlebar (3). -the handlebar height (3), if necessary. A WARNING: To be able to easily manoeuvre your sweeper, chose a comfortable and agreeable working position to suit your morphology. INSTALLING THE TOOL’S TILT SYSTEM...

TOOL PREPARATION - Position the tilt system at the attachment location, facing the mounting holes. - Install the 4 screws and washers. - Install the 4 washers and nuts on the other side. - Hold the screws in place with a 13 mm socket wrench and tighten the nuts with a 13 mm openjaw spanner. 13 mm openjaw spanner 13 mm socket wrench Turn the tilt adjustment knob (14) clockwise for easy access to the upper screws. Turn the tilt adjustment knob (14) counter-clockwise for easy access to the lower screws. - Place the tool shaft in the coupling slot of the sweeper.

TOOL PREPARATION - Pull on the coupling latch (9). -coupling latch (9). - Push the tool until it stops. ©After first installing the battery (see the 15 - 16 pages), it is possible to use the motor of the sweeper to assist you, thus facilitating the coupling of the tool. Adjust the driving speed to the position 'A-L' and press the forward drive command (see how to adjust the travel speed on the 17 page and the steering controls on the 20 page). Remove the holding cord (28) from the thread of the coupling latch (9). Make sure the coupling latch (9) is locked in the tool. If the rotary brush tool...

TOOL PREPARATION - Disconnect the power cable from the rotating brush (29) when uncoupling the rotating brush tool. -coupling latch (9). - Make sure that the coupling hook is not engaged in the grommet of the tool (brush orientation switch (23) in the 'O’ position). 9 28, - Make sure that the support wheels (10) are oriented to position A (see orientation of the support wheels on the 19 page). - Stand on the right side of the sweeper and hold the tool and the handlebar. - Pull the tool shaft out of the coupling housing of the sweeper. -the rotating brush (see orientation of the support wheels...

TOOL PREPARATION INSTALLING A WASTE COLLECTION BIN (OPTIONAL) The waste collection tray is an option that mounts onto the rotating brush tool. It collects the debris swept up by the brush. To empty the tray, simply remove it with its handle. - Fit the mounting brackets of the waste collection tray onto the support rods (12). - Slide the mounting brackets of the waste connection tray along the support rods (12) to the stop. - Make sure that the seal in the waste collection tray is placed under the protective cover of the rotating brush. - Remove the waste collection tray with its handle to empty...