PRODUCT INFORMATION | INTERIOR POLYX®-OIL RAPID The renowned Polyx®-Oil in a fast drying variation! 3262 Clear Matt 1 COAT PRODUCT DESCRIPTION Professional, fast drying, clear wood finish with special surface hardness that uniquely combines the advantages of natural oils and waxes in one product. Osmo Polyx®-Oil Rapid is stain-resistant, water-repellent and abrasion-resistant and results in a surface that is pleasant to the touch. In comparison to conventional finishes, the use of plant ingredients creates a more even colour and more harmonious appearance. Simple application – without primer or intermediate sanding – this saves time and money. Suitable for wood; microporous surface will not crack, peel, flake or blister. Resistant against wine, beer, cola, coffee, tea, fruit juice, milk and water in accordance with German DIN 68861-1A – no water spots. The dry finish is safe for humans, animals and plants (resistant to saliva and perspiration acc. German DIN 53160, suitable for children‘s toys acc. EN 71.3). RECOMMENDED USE Osmo Polyx®-Oil Rapid is ideal for the protection of all wooden floors, such as solid wood, plank, strip, OSB and cork flooring, as well as for furniture surfaces. INGREDIENTS Based on natural plant oils and waxes (sunflower oil, soya oil, thistle oil, carnauba wax and candelilla wax), paraffin, siccatives (drying agents) and water-repellent additives. Dearomatized white spirit (benzene-free). EU limit value for this product (cat. A/i): 500 g/l VOC (2010). This product contains max. 500 g/l VOC. Detailed declaration of ingredients available upon request. TECHNICAL DATA Specific gravity: 0.88-0.95 g/cm³ Viscosity: 25-45s DIN EN ISO 2431/4 mm, thixotropic Odour: faint/mild, after drying odourless Flash point: 35-52°C acc. DIN EN ISO 2719 STORAGE Up to 5 years and longer if can is kept dry and closed tightly. If thickened by frost, store for 24-36 hours at room temperature before use. SURFACE PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 18%). Osmo Polyx®-Oil Rapid is ready to use. Do not thin. Stir well before use. Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. Fill small cracks, larger joints or holes in wood (with Osmo Wood Filler). Sand wood surfaces carefully. Begin with coarse sandpaper – final sanding work for flooring P120150, for furniture P180-240. Before oiling the surface, remove sanding dust with a broom or vacuum. The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. METHODS OF APPLICATION With Osmo Flat Brush, Microfibre Roller or Floor Brush, apply thinly and evenly to the clean and dry wood along the wood grain and spread well within 10-15 minutes. Wipe away any excess product. Allow to dry for approx. 4-5 hours under good ventilation. After drying, apply a second coat also thinly and quickly. When renovating or recoating an already oiled surface, one coat applied to the clean and dry surface is usually sufficient. Page 1 - POLYX®-OIL RAPID Osmo Holz und Color GmbH & Co. KG · Affhüppen Esch 12 · D-48231 Warendorf Phone +49 (0)2581/922-100 · Fax +49 (0)2581/922-200 · info@

PRODUCT INFORMATION INTERIOR CLEANING OF TOOLS With Osmo Brush Cleaner (free of aromatic compounds). DRYING TIME Approx. 4-5 hours (normal climatic conditions, 23 °C/ 50 % rel. humidity). Lower temperatures and/or higher air humidity can increase the drying time. Ventilate well while drying. After 2-3 weeks, surface is fully cured. COVERAGE 1 litre covers approx. 24 m2 with one coat. Coverage depends significantly on the condition of the wood. All information refers to smooth and planed/ sanded surfaces. Other surfaces may lead to differences in coverage. NOTE Oils enhance the natural tone of...