ULTRASATEN TECHNICAL DATA SHEET
3Pages

Technical Data Sheet INT/us/03/en TECHNICAL DATA SHEET Technical Qualities ULTRASATEN is a low environmental impact, acrylic enamel for walls, that comes in a gloss, matt or satin finish. The product is self-expanding, scratch resistant and resistant to abrasion. ULTRASATEN guarantees good coverage with low thickness, a high yield, great washability and excellent resistance to yellowing, to alkali (ammonia and sodium solutions) alcohol, chemical detergents and dirt retention. Easy to clean and wash, it is ideal for public premises such as schools, hospitals, offices etc. By mixing Ultrasaten with Biamax, it is possible to create plush decorative finishes with a grainy effect. It is a product of the highest quality and has been put through all the tests indicated by the UNI 11021:2002 regulations for “Products and systems for painting environments where there are food stuffs present”. It has a low level of odour is, non-inflammable and friendly to both humans and the environment. Ideal Use Interior walls to be decorated, especially when subject to abrasion or dirt. Base coat for decorative products. Surface Preparation Clean the surface, removing any loose material. For crumbly or very absorbent substrates, apply the recommended acrylic fixative CRILUX or NEOFIX by OIKOS. Wait at least 6 hours before painting. In order to increase the coverage of the cycle use as primer IL PIGMENTATO by OIKOS. In the event that the decoration requires a perfectly smooth finish, screed over the surface first with STUCCO IN PASTA PER RASATURA (paste screed for walls) by OIKOS Application Method Apply two coats of ULTRASATEN diluted 20 ÷ 25% with drinkable water, leaving 4 ÷ 6 hours between each coat. ULTRASATEN can be applied by roller, brush or spray gun. It is a self-expanding product that does not leave signs of roller or brush strokes. By adding one litre of Biamax 03 base TR to four litres of Ultrasaten (Gloss, Satin or Matt), it is possible to obtain a mix with which very particular decorative effects can be created: Sabbiato Effect: on a smooth surface apply by brush, in an irregular manner, one coat of the ULTRASATEN/Biamax mix, diluted 20-25% with water. After a few minutes, pass back over the surfacewith the brush free of product, in order to highlight and bring out further the effect. If the coverage is not sufficient, after 4 – 6 hours a second coat can be applied. The yield varies according to the quantity of product applied. Yield 9-10mq/lt For this finish it is also possible to obtain the Stellato effect by adding two pots of the additive Decorglitter for every litre of the mix that is created. Le Trame Effect: on a smooth surface apply one coat of Fondo Murales. After drying, using a brush, apply one coat of the ULTRASATEN/Biamax mix diluted 15% with water, taking care to pass over the product for the last time in a horizontal direction, immediately work over the surface by dragging the Tool for Corduroy effect (art. 133) in the same direction. In order to eliminate eventual imperfections caused by accumulations of product, before the product is dry, pass back over the surface with the Spatola Dentata (art.A01). Once dry, repeat the operation, always applying the product in a horizontal Technical Data Sheet INT/us/03/en sense but working over the surface with the Tool for Corduroy effect in a vertical sense and using the Spatola dentata to remove eventual imperfections. It is essential to regularly clean excess product from the Tool for Corduroy effect in order to avoid the formation of lumps. Yield 4-5mq/lt. For this finish it is possible to obtain the Stellato effect by adding one pot of the additive Decorglitter to every litre of the mix gener

Technical Data Sheet INT/us/03/en These effects can also be used as the base for the application of other Oikos decorative products thus further enlarging the range of decorative finishes that can be achieved. In these instances it is best to mix Biamax into the MATT version of ULTRASATEN Finishes Dilution: Yield: Application tools: Primers: Application temperature: Drying time tack free: Drying time fully cured: Tools cleaning: 20-25% with drinkable water, Le Trame 15%. 9-11 m2/l in two coats. Le Trame 4 + 5 m2/l, Sabbiato 9 + 10 m2/l Brush, roller or spray gun (1.7 mm nozzle) Tool for...

Technical Data Sheet INT/us/03/en movement and transportation of the product; the containers, residue, eventual spilt material should be cleaned up using absorbent inert material such as sand, soil etc. etc. and then disposed of in accordance with the regional and national regulations in force at that time. Transportation must be carried out in accordance with international agreements. Specifications Clean the surface, removing any loose material. For crumbly or very absorbent substrates, apply an acrylic fixative as CRILUX or NEOFIX by OIKOS. In order to increase the coverage of the cycle...