INSTRUCTION PROLUXE MANUAL ™ convertible converts in seconds! ...then back to a portable! your portable table converted to a lift table www.oakworks.com · 717.235.6807 and back again

© Copyright 2011 Oakworks® , Inc. Notice Manual Part # MMMNST0022 1st Edition, January 2011 Printed in U.S.A. All rights are reserved. No part of this document may be photocopied, reproduced or translated to another language without prior written consent of Oakworks®, Inc. Oakworks® is a registered trademark of Oakworks®, Inc. The information contained in this document is subject to change without notice and should not be construed as a commitment by Oakworks®, Inc. Oakworks®, Inc. assumes no responsibility for any errors that may appear in this document nor does it make expressed or implied...

SYMBOL IDENTIFICATION - WARNINGS & CAUTIONS SYMBOL ID & WARNINGS SYMBOL IDENTIFICATION This symbol, when used in this manual and on product labels, represents a caution warning. Be sure to read and comply with all precautions and warnings. This symbol, when used in this manual and on product labels, warns against an electrical shock hazard. Be sure to observe and comply with all warnings. This symbol, when used in this manual or on product labels, indicates a Protective Earth (Ground) Terminal. This symbol when used in this manual or on product labels, warns that during transport there should...

GROUNDING GROUNDING INSTRUCTIONS This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electrical current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. See U.S. sample below. GROUNDING GROUNDING INSTRUCTIONS This product is manufactured for use on a nominal 120-volt circuit for the United States and...

DIRECTIONS FOR USE DIRECTIONS FOR USE PRODUCT DESCRIPTION knobs (4) wheels (2) End bumper of portable table support electric motor Adjustable portable table supports (2 sets) Center alignment groove Portable table secure strap Strap cleat Hook behind the cleat TABLE SPECIFICATIONS • Height Range: 20” - 36” • Width: fits portable tables 27” - 33” wide • Lift Capacity: Weight limit is defined by the portable table used with this product. (If the portable table has a weight limit of 450 lbs, then the system is 450 lbs) up to a maximum of 550 lbs. • Top: works with rectangular, round corner, or backrest...

PREPARE YOUR PROLUXE CONVERTIBLE PREPARE YOUR PROLUXE CONVERTIBLE ONE TIME ONLY PROLUXE CONVERTIBLE SET-UP This is a one time only procedure for each given portable table. STEP 1 Loosen all knobs below the adjustable portable table supports by turning the knob counter-clockwise. STEP 2 Slide the adjustable portable table supports to their widest position. STEP 3 Remove the portable table secure strap from the strap cleat (if necessary). STEP 4 Plug in the Convertible and lower to its lowest height 4

PREPARE YOUR PROLUXE CONVERTIBLE PREPARE YOUR PROLUXE CONVERTIBLE STEP 5 Open your portable table on its side. CAUTION Follow your table manufacturer’s instructions for using the Shiatsu option if your table has them. The instructions shown here are for general reference only. STEP 6 Remove the shiatsu cables or bolts on one side to enable your table to lay flat. There are different types of shiatsu cables. Follow the directions below based on the type you have. Or follow your table manufacturer’s instructions. Location of Shiatsu release bolts or wing nuts WING NUT Repeat these steps on both...

PREPARE YOUR PROLUXE CONVERTIBLE PREPARE YOUR PROLUXE CONVERTIBLE STEP 6 With your ProLuxe Convertible at its lowest height, stand at the side where the portable table supports are towards the outside, as shown here. Have the widest side of the adjustable portable table supports facing you. STEP 7 Load your portable table A Lift your portable table onto the ProLuxe Convertible base. B Open your portable table so that it is flat and position the bottom away from you. C Lower your portable table onto the ProLuxe Convertible base. CAUTION Be sure to read and follow the directions on how to center...

PREPARE YOUR PROLUXE CONVERTIBLE PREPARE YOUR PROLUXE CONVERTIBLE STEP 8 Once your portable table is on the ProLuxe Convertible, you are ready to align & secure it to the base. A Align the hinge of the portable table over the center alignment groove. Hinge of portable table Center alignment groove B Visually center the portable table with the base of the ProLuxe Convertible on both ends. C Be sure that the knobs are loose so you can adjust the table supports. D Keeping the portable table centered, push the adjustable table supports together against the sides of your portable table. 7

E Once the table supports are snug against the sides of the portable table, tighten the knobs to secure into place. NOTE: On tables with a backrest, leave a little space between the end bumpers and the backrest before tightening to allow movement of the backrest. F Double check that the hinge of the portable table is still aligned over the center alignment groove. PREPARE YOUR PROLUXE CONVERTIBLE PREPARE YOUR PROLUXE CONVERTIBLE G Insert strap into the center of the table. Attach one end of the strap as shown. Hold strap with one hand and with the other hand, slide strap thru the cleat. Then,...

DIRECTIONS FOR USE LOADING YOUR PORTABLE TABLE DIRECTIONS FOR USE This is done every time you remove and replace your portable table. All the adjustments to the base do not need to be done again. STEP 1 Open your portable table on its side. CAUTION Follow your table manufacturer’s instructions for using the Shiatsu option if your table has them. The instructions shown here are for general reference only. STEP 2 Remove the shiatsu cables or bolts to enable your table to lay flat. There are different types of shiatsu cables. Follow the directions below based on the type you have. Or follow your...