SHORT DESCRIPTION INDEPENDENT PARKING ON 2 LEVELS INCLINED ACCESS TO THE PLATFORMS PLATFORMS‘ INCLINATION: ABOVE 4,5°, BELOW 6,5° SINGLE SYSTEM (2 CARS), DOUBLE SYSTEM (4 CARS) LOAD PER PARKING SPACE: 2.000 KG (STANDARD) UP TO 2.300 KG (OPTIONAL) A P P L I C AT I O N F0R INTERIORS, WITH PIT ONE AND MULTI-FAMILY DWELLINGS HOTELS AND OFFICE BUILDINGS CONDOMINIUMS AND COMMERCIALS ABOVEGROUND AND READYMADE GARAGES FOR PERMANENT USERS ONLY

K i p p ar ker N3 3 0 2 NOTE The total height of the car including roof rail and antenna xture must not exceed the maximum car height mentioned in the table below. Standard cars do not feature sport equipment (e.g. spoiler, etc.). 140 Inclined access to the platforms Free space for gates Free space All dimensions in cm Pit depth back (GT-B) Incline acc. to DIN1045-1 Drainage channel 10x10 cm with collecting pit 50x50x20 cm For permanent and instructed users only Clear height for a lintel as per local or national requirements Platforms‘ inclination: above: 4,5° below: 6,5° min.18 In case of partition...

Services covered by the NUSSBAUM Company Installation diagram QUANTITY DESCRIPTION Hydraulic power unit with three-phase motor 230/400V, 50Hz, 3,0kW Control cable 4G1 (Control by standard keyoperated switch) Control cable 4G1 (by lockable switch) Empty conduit height: +170 cm Positions 1 to 5 are covered by the Nussbaum company unless otherwise agreed Empty conduit height: +120 cm Electricity meter Blade fuse or circuit breaker 3x 16A, slow acc. to DIN VDE 0100 part 430 Supply line 5x 2,5mm² (3 PH + N + PE) with marked leads + protective earth conductor to the mains switch 1x power unit Lockable...

K i p p ar ker N3 3 0 2 All dimensions in cm. All dimensions are minimum dimensions. Advice for planning and tendering: Generally masonry and concrete works are to be conducted according to the German norm VOB/C (DIN 18330 and DIN 18331). In the mentioned norm are pointed the tollerances that are to be fullled accor- ding to DIN 18202. In this norm are dened the maximum permissible dimension variations as exceedance and shortfall of the nominal size. The nominal size should be planned in order to meet the minimum dimensions necessary for the parking system. PA R T I T I O N WA L L S Single system...

5 All dimensions in cm. All dimensions are minimum dimensions. Advice for planning and tendering: Generally masonry and concrete works are to be conducted according to the German norm VOB/C (DIN 18330 and DIN 18331). In the mentioned norm are pointed the tollerances that are to be fullled accor- ding to DIN 18202. In this norm are dened the maximum permissible dimension variations as exceedance and shortfall of the nominal size. The nominal size should be planned in order to meet the minimum dimensions necessary for the parking system. Single system for 2 cars Double system for 4 cars surface...

K i p p ar ker N3 3 0 2 NOTE We suggest periodical maintainance, care and cleaning. Take advantage of NUSSBAUM maintainance Single system: consisting of 2 Platforms, 2 Power unit „Silencio“ For a list of services and interfaces please see the respective Table in this brochure. packed columns with hydraulic cylinders, lifting slide and hydraulic block, 2 rigid pillars • Synchronization unit to guarantee synchronous run even in case of irregular Double system: consisting of 4 Platforms, load distribution. 2 packed columns with hydraulic cylinders, With hydraulic canalization and with lifting slide...

7 NOTE We suggest periodical maintainance, care and cleaning. Take advantage of NUSSBAUM maintainance DRIVING SHEETS Parking space length: 510 cm Ramp if doorjambs are missing for the Parking space widths: 240 to 250 cm installation of the door slide rails. The pit must then be at least 535 cm long. Parking space height: up to 165 cm CO R R O S I O N P R OT EC T I O N Fastening of the parking system with Upper platforms with Aluminium-bulb C4-Line: driving sheets powdered on both chemical anchors in case of heighthened plates driving sheets and special driving foundation requirements. wedge to...

S E RV I C E S TO B E P ROV I D E D BY T H E C U S TO M E R A N D P L A N N I N G I N D I C AT I O N S During the planning phase please observe and comply with the following notes! Safety fences Electrical installation Prior to starting the assembly the cus- The customer must provide a 10 cm wide must be provided by the customer. tomer must provide a lockable main yellow-black marking on the front pit control switch out of the system/pit close edge according to the norm ISO 3864. Parking spaces‘ numeration to the power unit. Electrical services to For the allocation of the parking spaces be provided...