START-S4XL
1 / 14Pages

Earth -wire Reset of the control board: Press button “CODICI” and “TIMES” for 10 seconds COMMON contacts - Photocell always working PEDONALE Botton Start Button Light / Lamp. Closing photocell Light / Lamp. Open. Limit Switch Mot.1 Clos. Limit Switch Mot.1 Open. Limit Switch Mot. 2 Clos. Limit Switch Mot. 2 • • • • Single phase for 230 Vac 2 motors Universal control unit for 1 or 2 motors swing 4 limit switches Separate slow down SLOW DOWN

This manual provides all the specific information you need to familiarize yourself with and correctly operate your unit. Read it very carefully when you purchase the instrument and consult it whenever you have doubts regarding use and before performing any maintenance operations. START-S4XL is the ongoing evolution of the START-S4 electronic control unit, completely compatible and equipped with a sophisticated electronic circuit that controls the motive force, detecting any obstacles at any point in its operation. Safety precautions Using the unit improperly and performing repairs or...

2.2 Type of electrical wires According to the installations , to the type and the quantity of the cables, the wires can be different, in the table is shown the necessary cables for a standard installation. The installation cables should be conformed to the IEC 60335 norm. Power supply cable Motor cable (if it is not required) Lamp cable Antenna type RG58 Cable for key selector Cable for Photocell ‘s receiver Cable for Photocell’s transmitter 2.3 STANDARD INSTALLATION It is important to make an important risk analysis of the “ MACHINE” and of the customers requirements in order to decide how...

2.5 Description of the connections 230 Vac Neutral 230 Vac electrical power supplì 50 Hz Neutral 230vac electrical power supply 50 Hz Phase Outputs for LAMP (flashing light electronic card) or 230 VAC COURTESY LIGHT Output for the connection of motor 1 COMMON POLE M 1 Output for the connection of motor 1 POLE OPEN MOTOR 1 Outputs for connections motor no.1 pole CLOSE Output to connect motor no.2 pole common M2 Output to connect motor no.2 pole OPEN M2 Output to connect motor no.2 pole CLOSE Input Closing limit switches motor no.2 Input Opening Limit Switches 2 Input for Closing limit...

230 Vac control board power supply 230 Vac motors power supply and 230Vac lamp Accessories power supply and services and securities inputs Output for 12 Vac 50 Hz 1 A electrical lock, is powered for 3 seconds only by opening Commands, safeties, antenna Free contact for light indicating open gate or lamp without flashing card. Fototest and accessories tension and inputs for services and safeties. button for working time learning and setting up of “ VELOCE ”( fast) of the pause –time. For PEDESTRIAN ( partial opening ) learning time keep pressed till the opening of the MOTOR 1 button to...

The control board has several micro-switches to activate a lot of functions in order to find suitable solutions for the user and to make the installation more safety. By every order it inverts: open and close. It closes automatically at the end of the pause time shared property operation by opening and pause time it doesn’t accept commands. it recloses automatically at the end of the pause time By every command it follows the procedure open-stop-close-stopopen etc. It doesn’t re-close automatically By every command it follows open-stop-close-stop-open etc. It recloses automatically at the...

This function can able the “ Man present” function, The START command opens the closing PEDONALE command. The motors stop when the command has been released. (*see note) the PEDONALE command has closes while the START COMMAND has the same function of the DIP 1 and DIP 2 Activate the rolling code function. The control board accepts ONLY HCS rolling code remote controls and it checks the rolling code counter. The remote controls cannote be copied. If it is enable it controlled gradual de part The motors has a minimum force for the de part and they can reach the planned values. This function...

Setting up and enables of the inputs in the DIP C Exclusion of the inputs closing limit switches of motor. No.2 Exclusion of inputs of the opening limit switches motor no.2 Exclusion of the inputs of the closing limit switches motor no.1 Exclusion of inputs of the opening limit switches motor no.1 Exclusion of the input of photocell working in closing. Exclusion of the input STOP Exclusion input photocell always activated.

Memorisation of the remote controls The control board can accept different type of codes, the first memorized remote control, define the type, consequentely, other type of codes (different from the first remote control) cannot be learnt. The control board accept standard codes from 12 to 64 bit and only the fixed part of the code for the rolling code HCS©, but using the DIP 13 ( 3 of DIP B) the rolling code counter can be checked. In this way the remote control cannot be copied. The memory capacity is about 200 rolling code remote controls. The first memorized remote control defines the...

TIME LEARNING The control board START S4XL has two way to plan the working time. NORMAL WAY: use this way when all doors are the same and the motors are the same. ADVANCED SYSTEM: use this way when you want top lan the exactly slown down and / or the doors have different functions ways. TIME LEARNING: NORMAL WAY The gate is in closed position 7 The automation is in the CLOSED position. * Push the button TIMES The first motor OPENS ... after the phase-deplacement, automatically... ... the second motor OPENS Push the button TIMES (or START) (If the opening limit switches are not available)...

5.2 TIME LEARNING: ADVANCED SYSTEM The gate is in closed position 7 Porre e lasciare in ON l’interruttore 10 del DIP A The gate is in closed position * Push the button TIMES The first motor OPENS Push the button TIMES (or START) If the slow down are active (trimmer see. Slow down) ... The first motor slows down when opening Push the TIMES button (or START) (if the opening limit switches of motor no.1is not available). Motor no.1 stops , the motor no.2 OPENS ... If the limit switch is available wait until the first motor stops Motor no.1 stops, then motor no.2 OPENS. Push the TIMES button...