ENGINE POWER MONOBOOM OFFSET BOOM SWING BOOM BUCKET CAPACITY With long arm and 450 mm rubber shoes

OUTSTANDING EFFICIENCY ULTRA QUIET OPERATION

EASY MAINTENANCE

EFFICIENT TIER 4 FINAL TECHNOLOGY GET THE MOST FROM YOUR FUEL New Holland midis feature a cutting-edge electronic high pressure common-rail engine that excels both in performance and low emissions level. An electronic control unit continuously analyses the best timing and quantities for the fuel injection and re-circulated exhaust gases into the combustion chamber. The result is optimal use of every drop of fuel, minimised emissions and low engine noise. TIER 4 FINAL WITHOUT DIESEL PARTICULATE FILTER (DPF) The stringent Tier 4 Final emissions standards are met without a DPF. This means there...

INTELLIGENT HYDRAULIC SYSTEM UNMATCHED CONTROLLABILITY The C-Series midis’ unmatched controllability is achieved with three pumps intelligently coordinated by an electro-hydraulic actuator. Three oil pressure sensors allow flow and pressure compensation, so that only the necessary oil flow is drained back to the oil tank. This way no fuel is wasted to move oil that is not required for the specific work load. EASY-TO-SWITCH WORKING MODES THE RESULTS ARE: Excellent controllability of each movement Top-class work performance Improved simultaneous movements Reduced fuel consumption TAILOR MADE PERFORMANCE...

ULTRA QUIET OPERATION REVOLUTIONARY INDR COOLING SYSTEM The New Holland mid-size crawler excavators feature the revolutionary Integrated Noise and Dust Reduction (iNDr) cooling system, which minimizes noise, optimises cooling and maximises particulate filtration. The Integrated Noise & Dust Reduction cooling system is an innovative solution that has solved the two key issues facing all cooling systems: noise & dust. The secret is the AIR flow management. The air goes through a filter first, ensuring that only clean air enters the engine. It then follows a duct, passing holes and joints, which...

THE IDEAL EXCAVATOR FOR URBAN JOBSITES SILENT, SAFE, CLEAN, FAST AND COMPACT New Holland midis are the best choice for customers who cannot compromise on performance and safety, but need to work in urban jobsites where low emissions, low noise and compact dimensions are essential. The short radius design minimises the risk of hitting the tail of the machine against obstacles or walls, allowing the operator to concentrate on the job. EASY TRENCH DIGGING WITH OFFSET BOOM Our unique offset boom is the ideal solution to dig trenches alongside a wall, since the operator has a direct view of the bucket...

PLENTY OF ROOM AND FEATURES Accessing the cab is easy thanks to the ergonomic handrails and a wide door. Legroom is generous and the double-slide seat and joysticks or seat-only slide adjustment enable the operator to find the ideal working position. A pneumatic cushioned and heated seat is available as a factory fitted option. Opening and closing the front window is easy with the one-touch lock release, and the lower front window can easily be removed and stored in the rear left area of the cab. OUTSTANDING VISIBILITY The new EVO cab provides excellent all-round visibility, with a full size...

CONVENIENT MAINTENANCE EASY MAINTENANCE GUARANTEED WITH: A fast and easy access to components, requiring regular maintenance, such as engine and hydraulic filters, hydraulic pumps and filters, cooling units, fuse box, air conditioner filters. Long service intervals: : hydraulic oil lasts 5000 hours. The oil filter has a 1000 hour replacement cycle. The double-element air filter has twice the service life of previous air cleaners. The self-diagnostic function provides an early-warning detection and display of any malfunctions in the electrical system, preventing severe damage. It also alerts when...

TELEMATICS INSIDE GPS POSITIONING INFORMATION GATHERING Your machine receives its GPS positioning Your machine collects its working condition, from the satellite. engine and Can-Bus information, and sends it to the New Holland FleetforceWeb Portal through the mobile networks.

LOWER MAINTENANCE AND OPERATING COSTS You can access the maintenance information of every unit in your fleet from your desk and receive alerts when a machine is due for service. The maintenance plans can be synchronised automatically with your dealer, so that they run smoothly and the good health of the entire fleet is maintained at all times. HEALTH CHECK AND BREAKDOWN PREVENTION New Holland’s telematics system will provide you with detailed performance information, such as engine load, fuel consumption and Can-Bus based reports, so that you will be able to detect immediately if any of your...

E75C SR ARM A - Overall length B - Overall width of crawler C - Overall height (to top of cab) D - Ground clearance of rear end E - Ground clearance F - Tail swing radius G - Tumbler distance H - Overall length of crawler I - Track gauge J - Shoe width K - Overall width of upperstructure L - Dozer blade (up/down) DIGGING FORCE E75C SR ARM Bucket breakout force Arm breakout force OPERATING WEIGHT 450 mm rubber shoes 600 mm rubber shoes

E75C SR MONOBOOM ARM Max. digging reach Max. digging reach at ground level Max. digging depth Max. digging height Max. dumping height Min. dumping height Max. vertical wall digging depth Min. swing radius Digging depth for 2.4 m flat bottom E75C SR OFFSET BOOM ARM Max. digging reach Max. digging reach at ground level Max. digging depth Max. digging height Max. dumping height Min. dumping height Max. vertical wall digging depth Min. swing radius Digging depth for 2.4m flat bottom E85C MSR ARM Max. digging reach Max. digging reach at ground level Max. digging depth Max. digging height Max. dumping...

E75C SR LIFTING CAPACITY- MONOBOOM E75C SR LIFTING CAPACITY- OFFSET BOOM RADIUS OF LOAD HEIGHT 3.0 m 4.5 m AT MAX REACH FRONT SIDE FRONT SIDE FRONT SIDE 1.80 1.80 1.41 1.41 1.51 4.5 m AT MAX REACH FRONT SIDE FRONT SIDE 1.75 1.75 1.69 E85C MSR LIFTING CAPACITY- SWING BOOM ARM 2.13 m, SHOE 450 mm RADIUS OF LOAD HEIGHT 3.0 m 4.5 m 6.0 m AT MAX REACH FRONT SIDE FRONT SIDE FRONT SIDE FRONT SIDE 1.07 1.07 1.57 All the lift capacity values are in tonnes and without bucket As per ISO 10567 the indicated load is no more than 87% of hydraulic system lifting capacity or 75% of static tipping load. Values...