ALUPANEL AluminiumComposite Panel

There is an increasing demand for well designed and thermally efficient external wall construction.The Rain Screen facade has proved to be an excellent alternative to standard non ventilated facade.The following Picture shows the basic principle of Rain Screen cladding. The advantages: Building structures are protected from heavy moisture and the damaging effect of solar radiation? Facade can breathe, providing optimal interior climate conditions ? Structural decay is decreased due to an elimination of condensation risks; this also gives greater insulation performance? Less heat transfer which...

K2System General View ALUPANEL XTALUP ANEL > fixing systems XT > Pic. 2 08.2007 1.2 size="-3">

fixing systems Wall Bracket B.3.1for systems K2.300 and K2.200Wall Bracket B.1.1for systems K2.100 and K2.50 Wall Bracket > Bracket Slider U.2.1 for systems K2.300 and K2.200Bracket Slider U.1.1for systems K2.100 and K2.50 Bracket Slider Carrier Slider K.1.1 Fixing Washer I.2.1Enforcing Washer I.1.1 Screw R.1Screw R.2 > 08.2007 1.3 size="-2">

K2Assembly. Solid Wall ALUPANEL XTALUP ANEL > fixing systems XT > Assembly on a solid wall 1. Make Lay-Out of the wall 2. Define the axis to start with 3. Define the place required for Wall Brackets of the lower Carrier. Depending on a project a Carrier can be supported by 2 or more Wall Brackets. Maximum recommended carrier length is 4 meters4. Drill holes for anchors 5. Clean the holes 6. Set anchors 7. Set Bracket Insulators, Wall Brackets and Enforcing Washers on Anchors shafts (Pic.3)8. Spin anchor nuts. Make sure that the teeth of the Enforcing Washer and Wall Bracket Correspond (Pic.4)9....

12. Carefully check if position of the Carrier is correct, if it isnt, untwist R screws and regulate carrier position. Once you are sure that the Carrier is in its place go to the Top Wall Bracket and twist two R.1 Screws up to the stop. As a result R.1 screws will cut the Carrier and lock it against vertical moves (Pic.8)13. Insert Carrier Sliders in the slot of the Carrier. Upper Carrier Slider of every cassette has to be directed upward by its notches (Pic.9). Lower Sliders will be directed downward by its notches. Fix Carrier Sliders slightly in their place using Set screws (Pic.11)14. Install...

Concrete frame Structure. Articles 1-9 are the same as for a solid wall 10. Take Carrier with Bracket Slider, Insert Carrier connector, with four Seal Elements installed inside the Carrier 160mm deep. Overlap the Bracket slider with the Wall Bracket. The distance between the edge of the carrier and the Wall Bracket should be 100mm. Take one R.1 Screw, put a Lock Washer and a Fixing Washer on it and screw it in the thread hole of the Bracket Slider until the sharp tip of the R.1 screw leans tightly to the Carrier and slightly cuts it. This means that the carrier does not slide under its own weight....

1. System is strong enough to install brackets every 4 meters for heights between 0-100m. It leads to anchors and time economy as well as to more effective insulation of the building2. Using specialied engineering software (Pic. 24) all of the system profiles show outstanding performances in strength, while using economic materials which creates a cost effective system3. Our systems are designed and manufactured to effectively compensate all possible temperature expansions (Pic. 20-23)4. This system can easily create smooth flat surfaces even if the underneath wall is uneven, this is due to our...

K2Head Detail ALUPANEL XTALUP ANEL > fixing systems XT > 1. C.2. Carrier 9. Insulation Membrane 2. B.1.1 Wall Bracket 10. Parapet Bracket 3. I.2.1 Fixing Washer 11. O.1. Bracket Insulator 4. R.1 Bolt 12. Anchor 5. DIN6798A Lock Washer d12 13. Insulation 6. K.1.1 Carrier Slider 14. J.1.1 Cassette Holder 7. Alupanel Cassette 15. DIN916 Set Screw M6x10 8. I.1.1 Enforcing Washer 16. DIN7337 Rivet 4x12 Al/A2 08.2007 1.16 size="-3">

K2Base Detail ALUPANEL XTALUP ANEL > fixing systems XT > 1. C.2. Carrier 9. Aluminium bracket 2. B.1.1 Wall Bracket 10. Perforated Alu Sheet 3. I.2.1 Fixing Washer 11. O.1. Bracket Insulator 4. R.1 Bolt 12. Anchor 5. DIN6798A Lock Washer d12 13. Insulation 6. K.1.1 Carrier Slider 14. J.1.1 Cassette Holder 7. Alupanel Cassette 15. DIN916 Set Screw M6x10 8. I.1.1 Enforcing Washer 16. DIN7337 Rivet 4x12 Al/A2 08.2007 1.17 size="-3">

K2Window Sill ALUPANEL XTALUP ANEL > fixing systems XT > 1. C.2. Carrier 10. Aluminium Profile2. B.1.1 Wall Bracket 11. Aluminium Profile 3. I.2.1 Fixing Washer 12. O.1. Bracket Insulator 4. R.1 Bolt 13. Anchor 5. DIN6798A Lock Washer d12 14. Insulation 6. K.1.1 Carrier Slider 15. J.1.1 Cassette Holder 7. Alupanel Cassette 16. DIN916 Set Screw M6x10 8. I.1.1 Enforcing Washer 17. DIN7337 Rivet 4x12 Al/A2 9. Aluminium Bracket 08.2007 1.18 size="-3">

K2Window Lintel ALUPANEL XTALUP ANEL > fixing systems XT > 1. C.2. Carrier 9. Roller Shutter 2. B.1.1 Wall Bracket 10. Aluminium Profile 3. I.2.1 Fixing Washer 11. O.1. Bracket Insulator 4. R.1 Bolt 12. Anchor 5. DIN6798A Lock Washer d12 13. Insulation 6. K.1.1 Carrier Slider 14. J.1.1 Cassette Holder 7. Alupanel Cassette 15. DIN916 Set Screw M6x10 8. I.1.1 Enforcing Washer 16. DIN7337 Rivet 4x12 Al/A2 08.2007 1.19 size="-3">