SINGLE-PLY ROOFING ACCESSORIES GUIDE

Product Spotlight JTS 1 is a moisture-cure urethane sealant made with 100% solids. JTS 1 seals large joints, roof termination bars and adheres to concrete, masonry, EPDM, PVC, TPO (primed), wood, vinyl and most other common building materials. • Isocyanate-free for improved stability & moisture tolerance for wet surface application • No sagging or shrinkage • Cures quickly with minimal odor • Submerge product and adhere under water with wet/dry application • Packaged in a durable plastic tube • Excellent workability • Contains less than 10 g/L allowable VOC content for areas with VOC transportation...

Helix® is a two-component, construction-grade, polyurethane foam adhesive designed to adhere approved roof insulations, thermal barriers, cover boards and fleece-backed single-ply membranes to acceptable substrates. Features and Benefits • Clean, odorless, fast one-step application resulting in significant labor savings for the contractor • Ready to use, no mixing • VOC, CFC, HCFC and solvent free • All purpose fleece back and insulation attachment formula • Full cure within minutes

EPDM MEMBRANES ETHYLENE PROPYLENE DIENE MONOMER STANDARD BLACK EPDM MEMBRANE (45 Mil & 60 Mil) Used as a elastomeric single-ply roofing membrane for new construction and reroofing applications. May be installed in ballasted and fully adhered roofing systems. Standard Black EPDM Membranes are Fire Retardant (FR) membranes. FR EPDM MEMBRANE (PRE-CLEANED 60 Mil & 90 Mil) Used as an elastomeric single-ply roofing membrane for new construction and re-roofing applications. Pre-cleaned 60 mil and 90 mil membranes are primarily used in fully adhered roofing systems, but can also be ballasted. STANDARD...

ACRYLIC WATER BASE BONDING ADHESIVE Used for single-side, wet, horizontal application of EPDM to acceptable HD wood fiberboard, plywood, OSB, DensDeck® Prime Roof Board or SECUROCK® Roof Board. Low temperature restrictions apply. BONDING ADHESIVE A high strength solvent-based contact adhesive that allows quick bonding of EPDM membrane and cured flashings to various porous and non-porous substrates. May be used on both horizontal and vertical surfaces. Formulated for application with a 1/2" (13 mm) medium nap roller.

EPDM X-23 LOW-VOC BONDING ADHESIVE A high-strength, solvent -based contact adhesive that bonds EPDM membranes to various porous and non-porous substrates.

TAPE PRIMER A solvent-based product designed for one-step cleaning and priming of EPDM surfaces to be bonded with In-Seam Tapes Uncured Flashing Tapes, Cured Cover Tapes and Pre-Taped membranes. LOW VOC PRIMER A low-VOC product designed for one-step cleaning and priming of EPDM and TPO surfaces prior to the application of In-Seam Tapes and other taped products. Specially formulated using a blend of VOC exempt and non-exempt solvents to be meet the < 250 g/L VOC content requirements of the OTC Model Rule for adhesives and sealants.

WEATHERED MEMBRANE CLEANER Used to clean in-service EPDM membrane that has been exposed to the weather and clean TPO membrane prior to the welding process. Helps to loosen and remove dirt and other contaminants from the surface of the EPDM and TPO membranes and leaves a suitable surface for welding or the subsequent application of Tape Primer. LOW-VOC WEATHERED MEMBRANE CLEANER *Meets California & Utah VOC regulations EPDM BLACK LAP SEALANT Required for sealing EPDM seams and flashings against the effects of weathering when seamed with Splice Adhesive or All Purpose Single Seal Adhesive. Refer...

6" REINFORCED EPDM MEMBRANE STRIPS (RMS) Used in conjunction with Mule-Hide 2.4" seam plates and Mule-Hide HDP fasteners as securement of the EPDM membranes at the base of parapet walls and curbs. Installed beneath the EPDM field sheet and used as an alternate method to using the Mule-Hide All Purpose Bar. Requires the use of Tape Primer or Low VOC Tape Primer. 9" REINFORCED EPDM MEMBRANE STRIPS (RMS) Available in a 9" width with two strips of pre-applied In-Seam Tape. Used to attach EPDM membranes horizontally in the field of the roof on mechanically fastened systems. Requires the use of Tape...

POURABLE SEALER POCKETS Ideal for sealing irregular, hard to flash penetrations through the membrane. Prefabricated pockets consisting of a 2" (50 mm) wide plastic support strip with attached Uncured EPDM Flashing Tape. Requires the use of Tape Primer or Low VOC Tape Primer. PREMOLDED EPDM PIPE BOOTS Accommodates single pipe sizes from 1" to 6" in diameter. Conical-shaped steps securely seal all single pipe penetrations. The large, double-thick, molded rib at the top of each step offers superior tear-resistance and reinforcement, as well as a cutting guide. Requires the use of Tape Primer or...

WALKWAY PADS WITH TAPE Designed to protect the membrane in areas exposed to repetitive foot traffic. Mule-Hide requires walkways to be installed at all traffic concentration points, such as roof hatches, access door, rooftop ladders, etc. regardless of traffic frequency. Walkways are also required if regular maintenance (once a month or more) is necessary to service rooftop equipment. Requires the use of Tape Primer or Low VOC Tape Primer. YELLOW WARNING STRIP Intended for use on EPDM or TPO roofing systems to provide a visual warning of an impending hazard (i.e. roof edge, deep drain sump, skylight,...

THERMOPLASTIC POLYOLEFIN TPO MEMBRANE STANDARD & FR (45 Mil & 60 Mil) Used in mechanically attached and fully adhered roofing systems in new construction, reroofing and recover (retrofit) applications. It may also be used as flexible membrane flashings for walls, curbs, etc. when installing TPO membrane roofing systems. The system must be installed over acceptable roof insulation or other suitable substrate. See the Mule-Hide TPO Specifications Manual for complete specifications and details. TPO WITH CLEAN FILM (60 Mil) Identical product to the TPO Membrane Standard & FR (above) except with a...