Estimating tips EPDM Accessories Adhesives & Sealants Acrylic Water Base Bonding Adhesive - 1 or 5 gal., apply 1-sided Bonding Adhesive (solvent base) - 5 gal., apply 2-sided Low-VOC Bonding Adhesive - 5 gal., apply 2-sided Pourable Sealer (2 part) - 1 gal. Pourable Sealer (1 part) - 1/2 gal. pouches Pourable Sealer Pockets – EPDM, 4", 6" or 8" Single Seal Adhesive - apply 2-sided Universal Single-Ply Sealant - 10.1 oz. tube WBBA-2000 Bonding Adhesive (water based) - 5 gal., apply 2-sided Water Cut-Off Mastic - 11 oz. tube Coverage Rates 100-120 sq. ft. per gal. 60 sq. ft. per gal. 60 sq. ft. per gal. 200 cubic inch per gal. 122 cubic inch per pouch 1 per detail 60 sq. ft. per gal 25 linear ft. per tube 60 sq. ft. per gal. 20 linear ft. per tube Seaming Black Lap Sealant - 11 oz. tube Black Splice Adhesive / White Splice Adhesive - 1 gal., apply 2-sided 3" In-Seam Tape - black or white 6" In-Seam Tape - black Low-VOC EPDM Tape Primer - 1 gal. Tape Primer - 1 gal. Weathered Membrane Cleaner - 1 or 5 gal. 20 linear ft. per tube 50 sq. ft. per gal. 100' long roll 100' long roll 250 sq. ft. per gal. 200 sq. ft. per gal. (2) 1 gal. or 5 gal. Flashings 6" Cured Cover Tape - black 12" Cured Cover Tape - black Pre-cut Inside/Outside Corners (7" x 9" pieces purchased separately) - black Premolded EPDM Pipe Boots with Clamps (1" to 6" dia.) - black Premolded EPDM Pipe Boots w/Tape & Clamps (1" to 6" dia.) - black or white RMS (Reinforced Membrane Strip) - requires use of splice adhesive RMS with 3" Tape 6" Uncured EPDM Flashing Tape 12" Uncured EPDM Flashing Tape 100 linear ft. per roll 50 linear ft. per roll 1 per “T” joint 1 boot per penetration 1 boot per penetration 6" wide x 100' long roll 6" wide x 100' long roll 100 linear ft. per roll 50 linear ft. per roll Fasteners 2.4" Seam Plates 3" Insulation Plates Drill Point Fasteners (for Insulation only) - #12 HDP Fasteners (for membrane/RMS only) - #14 EHD Fasteners - #15 Pre-Assembled Fasteners - #12 w/insulation plate 1,000 per pail 1,000 per pail 1,000/500 per pail* 1,000/500/250 per pail* 1,000/500/250 per pail* 250/200 per pail* *See price list for fastener length/QTY per pail Accessories All-Purpose Bar HP Protective Mat Poly ISO 1 Roof Insulation - flat Poly ISO 1 Roof Insulation - tapered Poly ISO 2 Roof Insulation - flat Poly ISO 2 Roof Insulation - tapered Mate-Line Tape - white, black Rubber Paver Blocks - black, terra cotta Pre-Taped Walkway Pads - black, white Yellow Warning Strip DensDeck® DensDeck® Prime SECUROCK® Adhesive types & uses 10 ft. long pieces 15' wide x 300' long 4' x 4' or 4' x 8' Sheets 4' x 4' Sheets 4' x 4' or 4' x 8' Sheets 4' x 4' Sheets 6" or 12" x 100' 24" wide x 24" long 30" wide x 30" long 12" wide x 100' long roll 4' x 8' Sheets 4' x 4'’ or 4' x 8' Sheets 4' x 8' Sheets Water Based AdhesiveS Acrylic Water Base Bonding Adhesive is used for singleside, wet, horizontal application of EPDM to acceptable HD wood fiberboard, plywood, OSB, DensDeck® Prime or SECUROCK®. Low temperature restrictions apply to this product. FAQ’s & Reference Guide Frequently Asked Questions WBBA 2000 Bonding Adhesive is a two-sided water based bonding adhesive used to adhere EPDM, TPO and PVC membranes to approved surfaces. WBBA 2000 may be used as a one-sided, wet lay-in adhesive with Mule-Hide Fleece Backed membranes. Low temperature restrictions apply to this product. Estimating Tips Select-A-Membrane Chart Adhesive Types & Uses Solvent Based Adhesives Bonding Adhesive (solvent base) to fully adhere EPDM and flashing materials to acceptable rigid insulation boards, metal, wood, masonry, & other acceptable substrates on both horizontal & vertical surfaces. Low VOC Bonding Adhesive is a high strength solventbased contact adhesive that allows bonding of EPDM and TPO membrane to various porous and non-porous substrates. It is specially formulated using a blend of VOC exempt and non-exempt solvents to be meet the < 250 g/l VOC content requirements of the OTC Model Rule for Single Ply Roofing Adhesives. Contact Mule-Hide Products for specific product approvals and ratings. Featured industry association/organization logos are U.S. registered trademarks. Mule-Hide is an AIA registered CES provider. Energy Star is only valid in the United States for Roofing Products. Black Splice Adhesive/White Splice Adhesive is a contact adhesive to adhere seams of EPDM and uncured flashing material to EPDM. May be only used for projects requesting up to 10 year System Warranties. Customer Line: 800-786-1492 • www.mulehide.com Check our website monthly for the latest updates & technical bulletins. National Support Center • 1195 Prince Hall Drive • Beloit, WI 53511 • tel. 608.365.3111 • fax. 608.365.7852 The information herein should not be considered all-inclusive and should always be accompanied by a review of the Mule-Hide specifications and guidelines and good application practices. This information herein is based upon data and knowledge considered to be true and accurate at the time of printing and is provided for the reader’s consideration, investigation and verification. No statement made by anyone may supersede this information, except when done in writing by Mule-Hide Products Co., Inc. Mule-Hide Products Co., Inc. does not warrant any results to be obtained. Statements concerning possible use of Mule-Hide products are made without knowledge of your particular roof and such an application may not be fit for your particular purpose. MULE-HIDE DISCLAIMS ALL WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, except written warranties attached to Mule-Hide products and written warranties signed by an officer of Mule-Hide. Visit the Mule-Hide website at www.mulehide.com prior to any installation for updated technical specifications and details. Mule-Hide is a U.S. registered trademark. DensDeck is wholly owned registered trademark of Georgia-Pacific Gypsum LLC/Georgia-Pacific Wood Products LLC. SECUROCK is wholly owned registered trademark of USG Corporation. All rights reserved. ©2002 Mule-Hide Products Co., Inc. • Printed in USA • M