PROTECTIVE ASPHALT COATINGS #102 FibRATEd Roof Coating Mule-Hide #102 Fibrated Roof Coating is a fiber reinforced, non-polymer modified asphalt roof coating that forms a flexible, weather resistant film, that has excellent adhesion to most surfaces. Miami Dade County Approved. Meets ASTM D4479 Type I. Coverage: Apply at the rate of approximately 2-3 gallons per square depending on job specifications. Approximately 4 gallons per square when used to adhere granules. Stir coating to uniform consistency before using. Avoid heavy mounds of mass accumulation. Container: 5 Gal The trusted name Mule-Hide asphalt cements and coatings install quickly, easily and safely with consistent performance both “On-the-Roof” & “Out-of-Pail”. Professional contractors: • Extraordinary Value from a Name You Trust Roof Mastics • Consistent Performance On-the-Roof & Out-of-the-Pail • The Products You Need in the Sizes You Need Mule-Hide #111 Non-Fibrated Roof Coating is a professional grade, non-polymer modified asphalt roof coating that forms a flexible, weather resistant film, that has excellent adhesion to most surfaces. Coverage: Approximately 2-3 gallons per square for typical application. 3-4 gallons per square to adhere granules. Stir coating to uniform consistency before using. Container: 5 Gal Protective Asphalt Coatings • Products That Apply Quickly, Easily, Safely #111 NON-FibRATEd Roof Coating Asphalt Primers Aluminum Coatings • Energy-Efficient Selling Points building owners: • Economical, Trusted Performance • Quick Application for Minimal Disruption #311 Non-Fibrated Emulsion Roof Coating Mule-Hide #311 Non-Fibrated Emulsion Roof Coating is an asphalt-based, clay emulsion roof coating that can be used as a protective coating over smooth surfaced asphalt built-up and modified bitumen membranes. Can also be used as a base coat for reflective coatings. This product does not flow when applied in thick coatings. After drying, stays in place even when exposed to elevated temperatures. Miami Dade County Approved. Meets ASTM D1227 Type III Class I. Coverage: Approximately 3-4 gallons per 100 sq. ft., dependent upon roof surface. Container: 5 Gal, 55 Gal Drum, 275 Gal Tote • Extended Roof Life • Excellent Roof Protection & Appearance • Environmentally Friendly & Energy Efficient Product Options #301 Fibrated Emulsion Roof Coating Mule-Hide #301 Fibrated Emulsion Roof Coating is an asphalt-based, clay emulsion roof coating. It is versatile and specially formulated to give excellent resistance to water. Superior formulation provides increased weather resistance and durability. This product does not flow when applied in thick coatings and when dry, will stay in place even when exposed to elevated temperatures. In addition, the solvent free formulations are water based and non-combustible, requiring no “red tag” labeling for fire hazard. Miami Dade County Approved. Meets ASTM D1227 Type III Class I. Coverage: Approximately 3-4 gallons per 100 sq. ft., dependent upon roof surface. Container: 5 Gal, 55 Gal Drum, 275 Gal Tote Customer Line: 800-786-1492 • www.mulehide.com ASPHALT PRIMERS Check our website monthly for the latest updates & technical bulletins. National Support Center • 1195 Prince Hall Drive • Beloit, WI 53511 • tel. 608.365.3111 • fax. 608.365.7852 Mule-Hide #121 Asphalt Primer is a general purpose penetrating asphalt primer used to promote adhesion prior to the application of hot-mopped, cold-applied and self-adhesive membrane systems, as well as roof cements, mastics, and asphalt-based adhesives. Miami Dade County Approved. Meets ASTM D41. Coverage: Approximately 1 gallon per square for typical application, depending on surface porosity. Container: 5 Gal ASPHALT CEMENTS & COATINGS Mule-Hide #121 Asphalt Spray Primer is manufactured from a rapid cure asphalt and refined solvents. This primer sprays easily and dries to a tough film that has good resistance to temperature change and provides a firm base with better adhesion of asphalt coating. Miami Dade County Approved. Meets ASTM D41. Container: 14 oz Can The information herein should not be considered all-inclusive and should always be accompanied by a review of the Mule-Hide specifications and guidelines and good application practices. This information herein is based upon data and knowledge considered to be true and accurate at the time of printing and is provided for the reader’s consideration, investigation and verification. No statement made by anyone may supersede this information, except when done in writing by Mule-Hide Products Co., Inc. Mule-Hide Products Co., Inc. does not warrant any results to be obtained. Statements concerning possible use of Mule-Hide products are made without knowledge of your particular roof and such an application may not be fit for your particular purpose. MULE-HIDE DISCLAIMS ALL WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, except written warranties attached to Mule-Hide products and written warranties signed by an officer of Mule-Hide. Visit the Mule-Hide website at www.mulehide.com prior to any installation for updated technical specifications and details. Mule-Hide is a U.S. registered trademark. All rights reserved. ©2012 Mule-Hide Products Co., Inc. • Pr

ROOF MASTICS ROOF MASTICS - cont. #211 Plastic Cement Mule-Hide #211 Plastic Cement is a general purpose formulation for use as a cold-applied sealing and repair material in many types of asphalt roof membranes. MuleHide #211 Plastic Cement has a heavy “trowel-grade” consistency which makes this product ideal for flashing details and a variety of waterproofing repairs, such as moving joints and roof penetrations. Mule-Hide #211 Plastic Cement has a superior formulation that will not separate. Miami Dade County Approved. Meets ASTM D4586. Coverage: Approximately 8 gallons per square for a 1/8"...