LED3W350iN-01

Product catalog summary

Ordering Information
This section provides fields for specifying the date, quantity, project, note, and type when ordering the LED3W350iN-01 product with a B driver enclosure.

Important Notes
1. Avoid installing an on-off switch on the output side of a constant current LED driver to prevent damage and voiding the warranty.
2. Follow MP Lighting's wiring instructions: series wiring for constant current drivers and parallel wiring for constant voltage drivers. Improper installation voids the warranty.

Specifications
The LED3W350iN-01 is a constant current, non-dimmable LED driver with a 3W, 350mA output and 100-240V AC input. It is suitable for damp and dry locations.

Dimensions
The driver dimensions are 2-5/8” x 7/8” x 1-3/8” (66mm x 22mm x 35mm), and with enclosure, it measures 6-1/4” x 5-1/8” x 2” (160mm x 130mm x 51mm).

Performance
Input voltage ranges from 100~240V AC, with an output voltage of 3~12V DC and a power factor of 0.9 minimum. The typical efficiency is 60%, and it supports a maximum wattage of 3.5W. The driver is not dimmable.

Recommended Load
Typically used for 1W LED fixtures, supporting 1 to 2 fixtures in non-dimming mode.

Application
Approved for damp and dry locations, with an ambient temperature range of -20°C to 65°C. The driver includes short circuit and overload protection and weighs 89.5g.

Wiring Diagram
Illustrates the non-dimming wiring setup for 1-2 x 1W LED lighting fixtures (350mA) wired in series.

Catalog excerpts

LED3W350iN-01 CONSTANT CURRENT 3W, 350mA, non-dimmable, 100-240V AC Input Damp, and Dry location Ordering Information Clear Form Specifications LED Driver | Example Code: LED3W350iN-01-B Product Important Notes Warranty Notes & Disclaimer MP Lighting reserves the right, at its sole discretion, at any time and without notice, to make improvements and innovations to any of our products. Consult MP Lighting website for further details. 1. Do not install on-off switch at the output (load) side of a constant current LED driver as it will damage the fixture(s) and will void the warranty on both driver and fixture(s). 2. Fixtures must be wired as per MP Lighting's instruction (series wiring for constant current driver and parallel wiring for constant voltage drivers.) Failures due to improper installation will void warranty. Dimensions Driver Driver with Enclosure (EBX-160-ZP) MP Lighting © | www.mplighting.com | [email protected] | 604.708.1184

Open the catalog to page 1

LED3W350iN-01 CONSTANT CURRENT 3W, 350mA, non-dimmable, 100-240V AC Input Damp, and Dry location Performance Input Power Factor: 0.9 minimum. Controls Dimming Protocols Dimming Range Recommended Load Driver Load Typically used for 1W LED fixtures with the load below: Systems Input Voltage System Dimming Option Application Environments Damp / Dry Location approved. Ambient Temperature Case Temperature Driver Protection Short Circuit & Overload protection Case Material Non-conductive white plastic. MP Lighting © | www.mplighting.com | [email protected] | 604.708.1184

Open the catalog to page 2

Wiring Diagram Non-Dimming | For use with 1-2 x 1W LED lighting fixtures (350mA), wired in series Non-Dimmable Driver MP Lighting © | www.mplighting.com | [email protected] | 604.708.1184

Open the catalog to page 3

All MP Design Inc. catalogs and technical brochures

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.

Brand list