LED25W350iZ-01

Product catalog summary

Ordering Information
This section provides placeholders for date, quantity, project, note, and type, along with the product enclosure type, which is 'B' for the driver enclosure.

Important Notes
1. Avoid installing an on-off switch on the output side of a constant current LED driver to prevent damage and voiding the warranty.
2. Follow MP Lighting's wiring instructions: series wiring for constant current drivers and parallel wiring for constant voltage drivers. Improper installation voids the warranty.

Specifications
The LED driver model LED25W350iZ-01 is a constant current programmable driver with a power rating of 25W, 350mA, and is 0-10V dimmable. It supports an input voltage range of 120~277V AC and is suitable for damp and dry locations (UL Class2).

Dimensions
Dimensions for the driver and driver with enclosure are provided in both inches and millimeters.

Performance

Input: 120~277V AC, 60 Hz
Output: 8~55V DC, 350mA constant current
Efficiency: Typical efficiency is 86%
Power Factor: Minimum of 0.9

Controls
The driver supports 0-10V dimming protocols with a dimming range of 1% to 100%. It is compatible with both dimming and non-dimming systems.

Recommended Load
The driver is typically used for 3-14 1W LED fixtures. The load specifications are consistent across different input voltages and dimming options.

Application
The driver is approved for IP20 environments, suitable for damp and dry locations, with an ambient temperature range of -30°C to 50°C. The maximum case temperature is 90°C. It includes short circuit, overload, and over-voltage protection. The driver weighs 226g and is made of metal.

Wiring Diagram
The diagram illustrates the wiring for dimming with 3-14 x 1W LED lighting fixtures (350mA), wired in series.

Catalog excerpts

LED25W350iZ-01 CONSTANT CURRENT PROGRAMMABLE 25W, 350mA, 0-10V dimmable, 120~277V AC Input Damp and Dry location (UL Class2) Ordering Information Clear Form Specifications LED Driver | Example Code: LED25W350iZ-01-B Product Important Notes Warranty Notes & Disclaimer MP Lighting reserves the right, at its sole discretion, at any time and without notice, to make improvements and innovations to any of our products. Consult MP Lighting website for further details. 1. Do not install on-off switch at the output (load) side of a constant current LED driver as it will damage the fixture(s) and will void the warranty on both driver and fixture(s). 2. Fixtures must be wired as per MP Lighting's instruction (series wiring for constant current driver and parallel wiring for constant voltage drivers.) Failures due to improper installation will void warranty. Dimensions Driver Driver with Enclosure (EBX-160-ZP) MP Lighting © | www.mplighting.com | [email protected] | 604.708.1184

Open the catalog to page 1

LED25W350iZ-01 CONSTANT CURRENT PROGRAMMABLE 25W, 350mA, 0-10V dimmable, 120~277V AC Input Damp and Dry location (UL Class2) Performance Input Power Factor: 0.9 minimum. Controls Dimming Protocols 0-10V dimmable. Can be used in both dimming & non-dimming systems. Dimming Range Recommended Load Driver Load Typically used for 3-14 1W LED fixtures with the load below: Systems Input Voltage System Dimming Option Application Environments IP20. Damp and Dry Location approved. Ambient Temperature Case Temperature Driver Protection Short Circuit, Overload & Over-voltage protection. Case Material MP Lighting...

Open the catalog to page 2

Wiring Diagram Dimming | For use with 3-14 x 1W LED lighting fixtures (350mA), wired in series Dimmable Driver MP Lighting © | www.mplighting.com | [email protected] | 604.708.1184

Open the catalog to page 3

All MP Design Inc. catalogs and technical brochures

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.

Brand list