LED18W350iP-01

Product catalog summary

Ordering Information
This section provides fields for specifying the date, quantity, project, note, and type for ordering the LED18W350iP-01 product with a B driver enclosure.

Important Notes
1. Avoid installing an on-off switch on the output side of a constant current LED driver to prevent fixture damage and warranty voidance.
2. Follow MP Lighting's wiring instructions: series wiring for constant current drivers and parallel wiring for constant voltage drivers to maintain warranty validity.

Specifications
The LED18W350iP-01 is a constant current LED driver with 18W, 350mA, ELV dimmable, and 120-277V AC input. It is suitable for damp and dry locations and complies with UL Class 2 standards.

Dimensions
Driver dimensions are provided, including measurements for the driver with enclosure.

Performance

Input: 120~277V AC, 50/60 Hz
Output: 4~52V DC, 350mA constant current
Efficiency: 80% typical
Power Factor: Minimum 0.9

Controls
ELV dimming is available at 120V only, with a dimming range of 10% to 100%. The driver can be used in both dimming and non-dimming systems.

Recommended Load
Typically used for 2W LED fixtures, with a load range of 2 to 12 fixtures for both dimming and non-dimming systems at 120V. For non-dimming systems, the same range applies for >120V~277V.

Application
Approved for damp and dry locations with an ambient temperature minimum of -30°C (-22°F) and a case temperature maximum of 80°C (176°F). The driver includes short circuit, overload, and over-voltage protection. It weighs 255g (0.56lb) and is made of steel.

Wiring Diagram
Illustrates wiring configurations for dimming and non-dimming setups with 2-12 x 1W LED lighting fixtures (350mA), wired in series.

Catalog excerpts

LED18W350iP-01 CONSTANT CURRENT 18W, 350mA, ELV dimmable, 120-277V AC Input Damp, and Dry location (UL Class2) Ordering Information Clear Form Specifications LED Driver | Example Code: LED18W350iP-01-B Product Important Notes Warranty Notes & Disclaimer MP Lighting reserves the right, at its sole discretion, at any time and without notice, to make improvements and innovations to any of our products. Consult MP Lighting website for further details. 1. Do not install on-off switch at the output (load) side of a constant current LED driver as it will damage the fixture(s) and will void the warranty on both driver and fixture(s). 2. Fixtures must be wired as per MP Lighting's instruction (series wiring for constant current driver and parallel wiring for constant voltage drivers.) Failures due to improper installation will void warranty. Dimensions Driver Driver with Enclosure (EBX-160-ZP) MP Lighting © | www.mplighting.com | [email protected] | 604.708.1184

Open the catalog to page 1

LED18W350iP-01 CONSTANT CURRENT 18W, 350mA, ELV dimmalbe, 120-277V AC Input Damp, and Dry location (UL Class2) Performance Input Power Factor: 0.9 minimum. Controls Dimming Protocols ELV dimming at 120V only. Can be used in both dimming & non-dimming systems. Dimming Range Recommended Load Driver Load Typically used for 2W LED fixtures with the load below: Systems Input Voltage System Dimming Option Application Environments Damp / Dry Location approved. Ambient Temperature Case Temperature Driver Protection Short Circuit, Overload & Over-voltage protection Case Material MP Lighting © | www.mplighting.com...

Open the catalog to page 2

Wiring Diagram Dimming | For use with 2-12 x 1W LED lighting fixtures (350mA), wired in series Maximum Dimmable Driver Dimmable Driver 350mA LED Lighting Fixture 350mA LED Lighting Fixture Non-Dimming | For use with 2-12 x 1W LED lighting fixtures (350mA), wired in series Maximum Dimmable Driver Dimmable Driver 350mA LED Lighting Fixture 350mA LED Lighting Fixture MP Lighting © | www.mplighting.com | [email protected] | 604.708.1184

Open the catalog to page 3

All MP Design Inc. catalogs and technical brochures

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.

Brand list