LED12W350iP-01

Product catalog summary

Ordering Information
This section provides a template for recording the date, quantity, project details, and type of product when ordering the LED12W350iP-01 driver with a B driver enclosure.

Important Notes
1. Avoid installing an on-off switch on the output side of a constant current LED driver to prevent damage and voiding the warranty.
2. Follow MP Lighting's wiring instructions: series wiring for constant current drivers and parallel wiring for constant voltage drivers to maintain warranty validity.

Specifications
The LED12W350iP-01 is a constant current driver with 12W, 350mA, and ELV dimmable features, suitable for 120V AC input. It is approved for damp and dry locations (UL Class2).

Dimensions
The driver dimensions are 1-1/4” x 4-7/8” x 3/4” and with enclosure, it measures 6-1/4” x 5-1/8” x 2”.

Performance

Input: 120V AC, 60 Hz
Output: 6~32V DC, 350mA constant current
Efficiency: 80% typical
Power Factor: Minimum 0.9

Controls
The driver supports ELV dimming protocols with a dimming range of 10% to 100% and is compatible with both dimming and non-dimming systems.

Recommended Load
Typically used for 1W LED fixtures with a load range of 2 to 8 fixtures for both dimming and non-dimming at 120V input.

Application
Suitable for damp and dry locations with an ambient temperature minimum of -30°C and a case temperature maximum of 90°C. The driver includes short circuit, overload, and over-voltage protection. It weighs 150g and is made of polycarbonate material.

Wiring Diagram
Illustrates the wiring setup for dimming and non-dimming applications with 2-8 x 1 Watt LED lighting fixtures (350mA) wired in series.

Catalog excerpts

LED12W350iP-01 CONSTANT CURRENT 12W, 350mA, ELV dimmable, 120V AC Input Damp and Dry location (UL Class2) Ordering Information Clear Form Specifications LED Driver | Example Code: LED12W350iP-01-B Product Important Notes Warranty Notes & Disclaimer MP Lighting reserves the right, at its sole discretion, at any time and without notice, to make improvements and innovations to any of our products. Consult MP Lighting website for further details. 1. Do not install on-off switch at the output (load) side of a constant current LED driver as it will damage 3/4” 20mm the fixture(s) and will void the warranty on both driver and fixture(s). 2. Fixtures must be wired as per MP Lighting's instruction (series wiring for constant current driver and parallel wiring for constant voltage drivers.) Failures due to improper installation will void warranty. Dimensions Driver Driver with Enclosure (EBX-160-ZP) MP Lighting © | www.mplighting.com | [email protected] | 604.708.1184

Open the catalog to page 1

LED12W350iP-01 CONSTANT CURRENT 12W, 350mA, ELV dimmable, 120V AC Input Damp and Dry location (UL Class2) Performance Input Power Factor: 0.9 minimum. Controls Dimming Protocols ELV dimmable. Can be used in both dimming & non-dimming systems. Dimming Range Recommended Load Driver Load Typically used for 1W LED fixtures with the load below: Systems Input Voltage System Dimming Option Application Environments Damp and Dry Location approved. Ambient Temperature Case Temperature Driver Protection Short Circuit, Overload & Over-voltage protection. Case Material MP Lighting © | www.mplighting.com |...

Open the catalog to page 2

Wiring Diagram Dimming | For use with 2-8 x 1 Watt LED lighting fixtures (350mA), wired in series Dimmable Driver Dimmable Driver 350mA LED Lighting Fixture Non-Dimming | For use with 2-8 x 1 Watt LED lighting fixtures (350mA), wired in series Maximum Dimmable Driver Dimmable Driver 350mA LED Lighting Fixture MP Lighting © | www.mplighting.com | [email protected] | 604.708.1184

Open the catalog to page 3

All MP Design Inc. catalogs and technical brochures

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.

Brand list