ETA European Technical Approval ETA-13/0515
9Pages

Deutsches Institut fur Bautechnik Zulassungsstelle fiir Bauprodukte und Bauarten Bautechnisches Priifamt Eine vom Bund und den Landern gemeinsam getragene Anstalt des offentlichen Rechts E-Mail: dibt@dibt.de provisions of Member States European Technical Approval ETA-13/0515 English translation prepared by DIBt - Original version in German language Trade name Vacupor NT-B2, Vacuspeed, Vacupor NT-B2-S, Vacupor PS-B2, Manufactunng plant Porextherm Dammstoffe GmbH Thermal insulation boards made of vacuum insulation panels (VIP) Porextherm Dammstoffe GmbH Diese Zulassung umfasst 9 Seiten This Approval contains 9 pages EuropSische Organisation fur Technische Zulassungen European Organisation for Technical Approvals

European technical approval English translation prepared by DIBt I LEGAL BASES AND GENERAL CONDITIONS 1 This European technical approval is issued by Deutsches Institut filr Bautechnik in accordance - Council Directive 89/106/EEC of 21 December 1988 on the approximation of laws, regulations and administrative provisions of Member States relating to construction products1, modified by Council Directive 93/68/EEC2 and Regulation (EC) N° 1882/2003 of - Gesetz uber das In-Verkehr-Bringen von und den freien Warenverkehr mit Bauprodukten zur Umsetzung der Richtlinie 89/106/EWG des Rates vom 21....

European technical approval English translation prepared by DIBt SPECIFIC CONDITIONS OF THE EUROPEAN TECHNICAL APPROVAL Definition of the product and intended use Definition of the construction product This European technical approval applies to the thermal insulation boards of vacuum insulation panels (VIP) and, if applicable, the respective top layers according to Table 1 glued on over the entire surface. The designations of the insulation boards are mentioned in Table 1. The thermal insulation boards consist of a supporting core of highly dispersed silicic acid, sealed under vacuum in a...

European technical approval English translation prepared byDIBt The thermal insulation boards are used for the thermal insulation of walls, floors and roofs within The thermal insulation boards may only be installed in structures where they are protected from precipitation, weathering and moisture. Regarding the application of the thermal insulation boards, the respective national provisions shall in addition also be observed. The provisions made in this European technical approval are based on an assumed working life of the thermal insulation boards of 25 years, provided that the...

European technical approval English translation prepared by DIBt The thermal conductivity of the vacuum insulation panels at a reference temperature of 10 °C is determined according to the standard EN 12667:2001-01. The top layers are neglected. The nominal value of the thermal conductivity is based on a limit value which must not be exceeded during production (category 2). The limit value of the thermal conductivity under dry conditions (before ageing) amounts to ^0,dry,iimit = 0.0053 W/(m- K) for "Vacupor NT-B2", "Vacupor PS-B2" and "Vacuspeed" as well as Xio.dry.iimK = 0.0044 W/(m- K)...

European technical approval English translation prepared by DIBt 2.13 Behaviour under point load The behaviour under point load at 5 % deformation is determined according to EN 12430:1998+A1:2006. The point load Fp amounts to at least 500 N for "Vacupor NT-B2" and 2.14 Tensile strength of the multi-layer metallized high-barrier foil The tensile strength of the multi-layer metallized high-barrier foil shall be determined in accordance with EN ISO 527-3 before and after ageing according to the EOTA assessment In the as-delivered condition and after ageing the tensile strength is at least 80...

European technical approval English translation prepared by DIBt The factory production control shall be in accordance with the control plan which is part of the technical documentation of this European technical approval. The control plan is laid down in the context of the factory production control system operated by the manufacturer and deposited with Deutsches Institut fur Bautechnik.10 The results of factory production control shall be recorded and evaluated in accordance with the provisions of the control plan. 3.2.1.2 Other tasks for the manufacturer The manufacturer shall, on the...

European technical approval English translation prepared by DIBt Assumptions under which the fitness of the product for the intended use was favourably The European technical approval is issued for the product on the basis of agreed data/information, deposited with Deutsches Institut fur Bautechnik, which identifies the product that has been assessed and judged. Changes to the product or production process, which could result in this deposited data/information being incorrect, shall be notified to Deutsches Institut fur Bautechnik before the changes are introduced. Deutsches Institut fur...

European technical approval English translation prepared by DIBt 5.1 Packaging, transport and storage The thermal insulation boards shall be packed such that they are protected from moisture and mechanical damage during transport and storage, and the vacuum is not destroyed by causing damage to the high-barrier foil. In the information accompanying the CE marking the manufacturer shall specify that the product shall be installed following the installation instructions of the manufacturer (only by trained specialized companies according to 4.2.2) and shall be protected from moisture and...