European Technical Assessment ETA-13/0549
11Pages

{{requestButtons}}

Catalog excerpts

European Technical Assessment ETA-13/0549 - 1

European Technical Assessment English translation prepared by DIBt - Original version in German language General Part Technical Assessment Body issuing the European Technical Assessment: Deutsches Institut für Bautechnik Trade name of the construction product MISAPOR Standard 10/75 MISAPOR Standard Plus 10/50 MISAPOR Dynamic 10/50 Product family to which the construction product belongs Factory made cellular glass loose fill Misapor Management AG Rossriedstrasse 2 7205 ZIZERS SCHWEIZ Manufacturing plant MISAPOR AG Werkstraße 32 CH-6252 Dagmersellen MISAPOR AG Bahnhofstraße 19 CH-7472 Surava This European Technical Assessment contains 11 pages including 1 annex which form an integral part of this assessment This European Technical Assessment is issued in accordance with Regulation (EU) No 305/2011, on the basis of This version replaces

Open the catalog to page 1
European Technical Assessment ETA-13/0549 - 2

European Technical Assessment ETA-13/0549 English translation prepared by DIBt The European Technical Assessment is issued by the Technical Assessment Body in its official language. Translations of this European Technical Assessment in other languages shall fully correspond to the original issued document and shall be identified as such. Communication of this European Technical Assessment, including transmission by electronic means, shall be in full. However, partial reproduction may only be made with the written consent of the issuing Technical Assessment Body. Any partial reproduction...

Open the catalog to page 2
European Technical Assessment ETA-13/0549 - 3

European Technical Assessment ETA-13/0549 English translation prepared by DIBt Technical description of the product This European Technical Assessment applies to cellular glass loose fills made of recycled waste glass powder. This foam glass gravel consists of factory made particles of cellular foamed glass, with typical size 10/50 mm or 10/75 (nominal sizes d/D). The cellular glass loose fills "MISAPOR" are manufactured in two standard classes. Depending on particle size the cellular glass loose fills are designated as follows: particle size ≤ 75 mm "MISAPOR Standard Plus 10/50" and...

Open the catalog to page 3
European Technical Assessment ETA-13/0549 - 4

European Technical Assessment ETA-13/0549 English translation prepared by DIBt Performance of the products and references to the methods used for its assessment For sampling, conditioning and testing the provisions of the EAD No. 040394-00-1201 "Factory made cellular glass loose fill" apply. Mechanical resistance and stability (BWR 1) Essential characteristic Oedometer modulus in accordance with ISO 17892-5:2017 and EAD No. 040394-00-1201, Annex A.1 "MISAPOR Standard 10/75" "MISAPOR Standard Plus 10/50", "MISAPOR Dynamic 10/50" Compressive stress at 10% deformation or compressive strength...

Open the catalog to page 4
European Technical Assessment ETA-13/0549 - 5

European Technical Assessment ETA-13/0549 English translation prepared by DIBt Essential characteristic Behaviour under cyclic loading acc. to EAD Load changes: 50 kPa and 200 kPa; Initial height of the compacted specimen 459 mm After 100 charges "MISAPOR Standard Plus 10/50", "MISAPOR Dynamic 10/50" Xtotal = 0.0085 m; Xload = 1.8 % After 500 charges Xtotal = 0.010 m; Xload = 2.2 % After 1000 charges Xtotal = 0.011 m; Xload = 2.4 % Loose bulk density in accordance with EN 1097-3:1998 "MISAPOR Standard 10/75" "MISAPOR Standard Plus 10/50", "MISAPOR Dynamic 10/50" Installation-specific...

Open the catalog to page 5
European Technical Assessment ETA-13/0549 - 6

European Technical Assessment ETA-13/0549 English translation prepared by DIBt Safety in case of fire (BWR 2) Essential characteristic Reaction to fire classified according to EN 13501-1: 2007+ A1:2009 * according to decision 96/603/EC (as amended) Hygiene, health and the environment (BWR 3) Essential characteristic Content, emission and/or release of dangerous substances CMR-Substances "MISAPOR Standard 10/75" "MISAPOR Standard Plus 10/50", "MISAPOR Dynamic 10/50" Substance/s classified as EU-cat. Carc. 1A and/or 1B a Substance/s classified as EU-cat. Muta. 1A and/or 1B a The product does...

Open the catalog to page 6
European Technical Assessment ETA-13/0549 - 7

European Technical Assessment ETA-13/0549 English translation prepared by DIBt Energy economy and heat retention (BWR 6) Essential characteristic Thermal conductivity test acc. to EN 12667:2001 and/ or EN 12664:2001 and EN 13167:2012+A1:2015, Annex A "MISAPOR Standard 10/75" "MISAPOR Standard Plus 10/50", "MISAPOR Dynamic 10/50" Moisture correction factor (condition 1) at water absorption in accordance with EN 12087:2013 determined "MISAPOR Standard 10/75" "MISAPOR Standard Plus 10/50", "MISAPOR Dynamic 10/50" Water absorption by total immersion (test duration 28 days) in accordance with EN...

Open the catalog to page 7
European Technical Assessment ETA-13/0549 - 8

European Technical Assessment ETA-13/0549 English translation prepared by DIBt Essential characteristic Capillary water suction height "MISAPOR Standard 10/75" "MISAPOR Standard Plus 10/50", "MISAPOR Dynamic 10/50" < 150 mm (at 8.3 kg/m2 moisture content after 21 days) < 150 mm (at 15 kg/m2 moisture content after 21 days) Assessment and verification of constancy of performance (AVCP) system applied, with reference to its legal base In accordance with EAD No. 040394-00-1201, the applicable European legal act is: 1995/467/EC The systems to be applied are: a) for uses as load bearing and...

Open the catalog to page 8
European Technical Assessment ETA-13/0549 - 9

Page 9 of European Technical Assessment ETA-13/0549 of 18 August 2020 MISAPOR Standard 10/75 MISAPOR Standard Plus 10/50 MISAPOR Dynamic 10/50 Table 1: Oedometer modulus MISAPOR Standard 10/75 Test specimen: Mean values of 8 tests on dry specimen Mean value of loose bulk density 149 kg/m3 (single value 133 - 163 kg/m3) Initial height of the compacted specimen 460 mm Degree of compaction 1.3:1 Initial thickness reduction, X0 (%) Total deformation, Xtotal Related thickness reduction, Xload (%) Oedometer Modulus, Eoed According to ISO 17892-5; Annex A.3 (kPa) MISAPOR Standard Plus 10/50,...

Open the catalog to page 9
European Technical Assessment ETA-13/0549 - 10

Page 10 of European Technical Assessment ETA-13/0549 of 18 August 2020 MISAPOR Standard 10/75 MISAPOR Standard Plus 10/50 MISAPOR Dynamic 10/50 Note: In case the cellular glass loose fill is used under concentrated/ centered loads an additional assessment could be necessary. Table 2: Shear parameter MISAPOR Standard 10/75 Test specimen: Mean value of density (after compaction) 177 kg/m3 Degree of compaction 1.3:1 Vertical stress load Shear displacement, Nominal shear stress MISAPOR Standard Plus 10/50, MISAPOR Dynamic 10/50 Test specimen: Mean value of density (after compaction) 205 kg/m3...

Open the catalog to page 10

All MISAPOR catalogs and technical brochures