StarTec XT The flexible multi-purpose formwork with the combination tie hole

Single-sided or two-sided tying Flexibility and costeffectiveness in the next generation The StarTec XT with the integrated combination tie hole unites three tying methods in one system. It is possible to switch between these with a flick of the wrist – without installing additional parts. You thus remain flexible and profit from significantly shorter formwork placing times when tying from one side. Another advantage: StarTec XT is fully compatible with StarTec and the lightweight, crane-independent AluStar. The StarTec XT multi-purpose formwork with its permissible fresh-concrete pressure capacity...

Simply smart Æ Size - Forming area up to 8.91 m² per panel (330 x 270 cm) - Panel heights 330, 270 and 135 cm and only 8 panel widths for t rouble-free corner solutions for all wall thicknesses Æ Performance - Permissible fresh-concrete pressure load (as per DIN 18218) of 60 kN/m² (DIN 18202, Table 3, line 6) Æ Universal use in commercial and residential housing construction Æ Closed steel profile - Structurally robust - Torsionally rigid - Hot-dip galvanised for easy cleaning and reduced concrete adhesion Integrated combination tie hole Select between three tying methods with a flick of the...

Enabled by the variable combination tie hole One system – 3 tying methods Single-sided tying with XT taper tie 20 Choose the best tying method! Every construction site is unique, and the formwork requirements vary from project to project. StarTec XT creates an ideal basis for this as the system ensures that you remain flexible and well equipped for every task. Thanks to the smart combination tie hole, it is possible to select between three tying methods with a flick of the wrist. Every panel can be used for both initial and final formwork without additional assembly work. This saves times and...

Single-sided tying with XT tie rod DW 20 and plastic tube Two-sided tying with tie rod DW 20 and plastic tube Combination tie hole on the final formwork side Combination tie hole on the initial formwork side Combination tie hole on the final formwork side Combination tie hole on the initial formwork side

Completely integrated The smart combination StarTec XT tie hole Ties with tapered anchor sleeves or DW 20 threads – the combination tie hole makes them possible. Combination tie hole in thread position By using an internal body that can be positioned as required with the XT combi-lever, the tying method can be changed easily with a flick of the wrist. The combination tie hole is integrated into the frame, e nsuring that no parts protrude. No installation and removal are required. Combination tie hole in anchor sleeve position

Small tool – huge impact The XT combi-lever The XT combi-lever is a universal f ormwork tool fitted with a karabiner that can be attached anywhere. Depending on the tying method, the XT combi-lever can be used in a wide variety of ways, e.g. - To set the tying method in the combination tie hole - To remove the XT sealing cone from the wall formwork panel

A wall full of ideas Typical StarTec – in every detail MEVA systems stand out due to a maximum of efficiency, quality and practical details. This also applies to the tried-and-tested multi-purpose formwork StarTec XT. With its uniform system components, small number of accessories and a perfectly coordinated range of options, has everything it takes to ensure that a MEVA system is the best solution for construction site applications. - Complete compatibility with StarTec and AluStar - Combinable with MEVA accessories Flange screw Single component for strong connection of all accessories Multi-function...

Fully compatible with lightweight AluStar Sealing cone XT sealing cone for initial and final formwork when tying from one side. AS assembly lock Only one component needed for rapid, reliable panel connection: MEVA assembly lock. Allows single-handed fitting at any position along the frame. A few hammer blows suffice to achieve a strong, level and stepless panel connection. Tie rod fixture Can be attached to the multi-function profile of the vertical or horizontal StarTec XT panel – for safe and rapid transport on the construction site. Sealing plugs Available in three versions to close off unused...

Optimally combined for single-sided tying XT taper tie 20 Wall thicknesses from 15 to 45 cm The XT taper tie 20 is available in various lengths for different wall thicknesses: - 15-25 cm - 20-30 cm - 35-45 cm The wall thicknesses are adjusted in 1 cm steps using spacers. The desired wall thickness can be read off the spacers. Integrated XT articulated flange nut Fixation screw Conical middle section Steel spacers for wall thickness (each 1 cm) and rubber buffer.

StarTec XT Inclinedcm H= 270 panels The clever XT combination tie hole and the XT taper tie enable a panel with an angle of inclination up to 4° to be tied simply and quickly. They can also compensate for angular misalignments up to 4° between adjacent and height-extended panels. The XT tie rod DW 20 is available in two lengths and can be used for all wall thicknesses. - 0-40 cm - 0-85 cm The wall thickness is determined by the length of the plastic tube. Plastic tubes D23 are available in the corresponding lengths for wall thicknesses of 20, 25, 30 and 35 cm. Integrated XT a rticulated flange...

Systematically planned StarTec XT panels and corners Tried-and-tested flexibility With the panel heights 330 cm, 270 cm and 135 cm as well as panel widths from 270 cm to 30 cm, StarTec XT enables quick adaptation to the geometry of the building. Thanks to the range of panels, all common wall thickness can be formed without filler areas. MPP Multi-purpose panel, width 75 cm IC Inside corner, with side length 25 cm OC Outside corner with side lengths 0 cm, 5 cm and 10 cm Furthermore, the system includes steplessly adjustable 60° to 180° hinged corners. Corner panels Hinged inside corner, with side...