*myarchiexpo

Catalogs
MBCI
5V -Crimp

5V -Crimp

Product catalog summary

Overview: The document outlines the design and installation guidelines for the 5V Crimp panel system, effective from November 1, 2011. It includes specifications, installation procedures, standards, compliance information, and recommendations to maintain warranty validity.

Specifications:

The minimum recommended slope for installation is 3:12. For slopes below this, consult MBCI.
Panels are 24" wide, available in 29 or 26 gauge Galvalume Plus® with a Signature® 200 coating.
Correct fastener application is crucial to prevent panel distortion and oil canning, which is not a rejection cause.

Installation Procedures:

Ensure a uniform substructure, typically ⁵⁄₈" plywood, to avoid panel distortion.
Install panels over a completely waterproofed substructure.
Follow detailed fastener patterns and spacing instructions for ridge, hip, and valley installations.
Specific steps include applying tape sealer, bevel cutting panels, and using Fastener #9 for valley installations.

Standards and Compliance:

Reference the North American Specification for Cold-Formed Steel Structural Members and applicable building codes.
5V Crimp panels meet UL 90 construction requirements and have a Class A fire rating over non-combustible substrates.

Recommendations:

Inspect all panels and accessories before installation; do not install if quality is questionable.
Consult MBCI for continuous panels over 25'.
Seal all panel ends at eave and valley conditions to prevent water ingress.

Contact Information: MBCI can be contacted at various locations across the United States for further assistance.

Typical Details:

Valley: Follow specified procedures for panel and closure installation.
Hip: Bevel cut panels to match the hip slope and use Tri-Bead tape sealer.
Rake Trim: Install with Fastener #9 through Tri-Bead tape sealer.
Alternate Drip Trim: Fasten to the roof deck with Fastener #13.
Eave Trim: Attach with Fastener #13 and apply urethane sealant.
Gutter: Fasten gutter straps with Fastener #14 and attach gutters with Fastener #13.
Slope Change: Install eave panels with Fastener #9 and apply sealant as specified.

Notes: Specifications and procedures may change without notice. Ensure compliance with building codes and industry practices. Visit the MBCI website for the latest information.

Catalog excerpts

5V Crimp Design/Installation Information

Open the catalog to page 1

IMPORTANT NOTICE READ THIS MANUAL COMPLETELY PRIOR TO BEGINNING THE INSTALLATION OF THE 5V CRIMP PANEL SYSTEM. MBCI DETAILS MUST BE FOLLOWED AS A MINIMUM TO INSURE APPROPRIATE WARRANTIES WILL BE ISSUED. ALWAYS INSPECT EACH AND EVERY PANEL AND ALL ACCESSORIES BEFORE INSTALLATION. NEVER INSTALL ANY PRODUCT IF ITS QUALITY IS IN QUESTION. NOTIFY MBCI IMMEDIATELY IF ANY PRODUCT IS BELIEVED TO BE OUT OF TOLERANCE, SPECIFICATION OR HAS BEEN DAMAGED DURING SHIPMENT. IF THERE IS A CONFLICT BETWEEN PROJECT ERECTION DRAWINGS PROVIDED OR APPROVED BY MBCI AND DETAILS IN THIS MANUAL, PROJECT ERECTION DRAWINGS...

Open the catalog to page 2

Houston, TX 877-713-6224 Adel, GA 888-446-6224 Atlanta, GA 877-512-6224 Atwater, CA 800-829-9324 Dallas, TX 800-653-6224 5V CRIMP Indianapolis, IN 800-735-6224 Lubbock, TX 800-758-6224 Memphis, TN 800-206-6224 Oklahoma City, OK 800-597-6224 Omaha, NE 800-458-6224 Phoenix, AZ 888-533-6224 Richmond, VA 800-729-6224 Rome, NY 800-559-6224 Salt Lake City, UT 800-874-2404 San Antonio, TX 800-598-6224 PRODUCT INFORMATION TABLE OF CONTENTS A. B. C. D. E. F. G. Architect/Engineer Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .V-2 General...

Open the catalog to page 3

Houston, TX 877-713-6224 Adel, GA 888-446-6224 Atlanta, GA 877-512-6224 Atwater, CA 800-829-9324 Dallas, TX 800-653-6224 Indianapolis, IN 800-735-6224 Lubbock, TX 800-758-6224 Memphis, TN 800-206-6224 Oklahoma City, OK 800-597-6224 Omaha, NE 800-458-6224 PRODUCT INFORMATION Phoenix, AZ 888-533-6224 Richmond, VA 800-729-6224 Rome, NY 800-559-6224 Salt Lake City, UT 800-874-2404 San Antonio, TX 800-598-6224 5V CRIMP ARCHITECT/ENGINEER INFORMATION 1. Minimum recommended slope is 3:12. For slopes less than 3:12, call MBCI. 2. Use a properly aligned and uniform substructure to avoid panel distortion....

Open the catalog to page 4

Houston, TX 877-713-6224 Adel, GA 888-446-6224 Atlanta, GA 877-512-6224 Atwater, CA 800-829-9324 Dallas, TX 800-653-6224 Indianapolis, IN 800-735-6224 Lubbock, TX 800-758-6224 Memphis, TN 800-206-6224 Oklahoma City, OK 800-597-6224 Omaha, NE 800-458-6224 Phoenix, AZ 888-533-6224 Richmond, VA 800-729-6224 Rome, NY 800-559-6224 Salt Lake City, UT 800-874-2404 San Antonio, TX 800-598-6224 PRODUCT INFORMATION 5V CRIMP GENERAL DESCRIPTION Coverage Width - 24" Minimum Slope - 3:12 Panel Attachment - Wood screws Panel Substrate - Galvalume Plus ® Gauges - 29 or 26 Finishes - Smooth or embossed ® Coating...

Open the catalog to page 5

Houston, TX 877-713-6224 Adel, GA 888-446-6224 Atlanta, GA 877-512-6224 Atwater, CA 800-829-9324 Dallas, TX 800-653-6224 Indianapolis, IN 800-735-6224 Lubbock, TX 800-758-6224 Memphis, TN 800-206-6224 Oklahoma City, OK 800-597-6224 Omaha, NE 800-458-6224 PRODUCT INFORMATION Phoenix, AZ 888-533-6224 Richmond, VA 800-729-6224 Rome, NY 800-559-6224 Salt Lake City, UT 800-874-2404 San Antonio, TX 800-598-6224 5V CRIMP UL 90 Requirements 5V Crimp Construction # 453 1. Metal Panels (26 gauge) – 24" wide, continuous over two or more spans. 2. Fastener spacing along the length of the panel is 3 feet...

Open the catalog to page 6

Metal Roof and Wall Systems * Fy is 80-ksi reduced to 60-ksi in accordance with the 2001 edition of the North American Specification For Design Of Cold-Formed Steel Structural Members - A2.3.2. Steel Structural Members. 4. Maxo is allowable bending moment. 5. All values are for one foot of panel width. 29 Gauge (Fy = 60 KSI) ALLOWABLE UNIFORM LOADS IN POUNDS PER SQUARE FOOT 26 Gauge (Fy = 60KSI) ALLOWABLE UNIFORM LOADS IN POUNDS PER SQUARE FOOT 1) Allowable loads are based on uniform span lengths and Fy = 60-ksi. 2) LIVE LOAD is limited by bending, shear, combined shear & bending and web crippling....

Open the catalog to page 7

Houston, TX 877-713-6224 Adel, GA 888-446-6224 Atlanta, GA 877-512-6224 Atwater, CA 800-829-9324 Dallas, TX 800-653-6224 Indianapolis, IN 800-735-6224 Lubbock, TX 800-758-6224 Memphis, TN 800-206-6224 Oklahoma City, OK 800-597-6224 Omaha, NE 800-458-6224 PRODUCT INFORMATION Phoenix, AZ 888-533-6224 Richmond, VA 800-729-6224 Rome, NY 800-559-6224 Salt Lake City, UT 800-874-2404 San Antonio, TX 800-598-6224 5V CRIMP PRODUCT CHECKLIST Panel Valley Ridge/Hip AG-237 Rake Trim AG-202 Specify Roof Pitch Drip Edge AG-250 AG-279 Outside Closure HW-452 Continuous Cleat HW-450 HW-504 Fastener #9 10 x 1¹⁄₂"...

Open the catalog to page 8

Houston, TX 877-713-6224 Adel, GA 888-446-6224 Atlanta, GA 877-512-6224 Atwater, CA 800-829-9324 Dallas, TX 800-653-6224 5V CRIMP Indianapolis, IN 800-735-6224 Lubbock, TX 800-758-6224 Memphis, TN 800-206-6224 Oklahoma City, OK 800-597-6224 Omaha, NE 800-458-6224 Phoenix, AZ 888-533-6224 Richmond, VA 800-729-6224 Rome, NY 800-559-6224 Salt Lake City, UT 800-874-2404 San Antonio, TX 800-598-6224 PRODUCT INFORMATION FASTENER PATTERNS EFFECTIVE NOVEMBER 1, 2011 SEE www.mbci.com FOR CURRENT INFORMATION SUBJECT TO CHANGE WITHOUT NOTICE V-7

Open the catalog to page 9

Houston, TX 877-713-6224 Adel, GA 888-446-6224 Atlanta, GA 877-512-6224 Atwater, CA 800-829-9324 Dallas, TX 800-653-6224 Indianapolis, IN 800-735-6224 Lubbock, TX 800-758-6224 Memphis, TN 800-206-6224 Oklahoma City, OK 800-597-6224 Omaha, NE 800-458-6224 PRODUCT INFORMATION Phoenix, AZ 888-533-6224 Richmond, VA 800-729-6224 Rome, NY 800-559-6224 Salt Lake City, UT 800-874-2404 San Antonio, TX 800-598-6224 5V CRIMP TYPICAL DETAILS RIDGE NOTES: 1. Stop panels 2" from center line of ridge. 2. Install first row of fasteners across panel to substrate 1'-0" down from bottom edge of ridge trim and space...

Open the catalog to page 10

Houston, TX 877-713-6224 Adel, GA 888-446-6224 Atlanta, GA 877-512-6224 Atwater, CA 800-829-9324 Dallas, TX 800-653-6224 5V CRIMP Indianapolis, IN 800-735-6224 Lubbock, TX 800-758-6224 Memphis, TN 800-206-6224 Oklahoma City, OK 800-597-6224 Omaha, NE 800-458-6224 Phoenix, AZ 888-533-6224 Richmond, VA 800-729-6224 Rome, NY 800-559-6224 Salt Lake City, UT 800-874-2404 San Antonio, TX 800-598-6224 PRODUCT INFORMATION TYPICAL DETAILS ALTERNATE RIDGE/HIP NOTES: 1. Stop panels 2" from center line of ridge. 2. Install first row of fasteners across panel to substrate 1'-0" down from bottom edge of ridge...

Open the catalog to page 11

All MBCI catalogs and technical brochures

Archived catalogs

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.

Brand list