Catalogs >
MAPEI >
ULTRABOND S997 1K

ULTRABOND S997 1K
1 / 4Pages

Catalog excerpts

One-component, solvent-free, ready-to-use, flexible, sililate polymer-based thixotropic adhesive for laying wooden steps and parquet mosaic Bonding wooden steps and profiles on all types of substrate, including in thick layers and installation of mosaics on walls. • easy to clean from surfaces. RECOMMENDATIONS • Apply at a temperature between +10°C and +35°C. Some application examples • GEV EMICODE EC1 R Plus. • Laying risers and treads on wooden stairs. • In particularly dry weather, the hardening time of the • Bonding wooden baseboards. product is longer. • Bead-laying three-layered, pre-finished parquet. • Installing wood mosaics on wall. TECHNICAL CHARACTERISTICS Ultrabond S997 1K is a hygro-hardening, thixotropic sililated-based adhesive, produced using technology developed in MAPEI’s own laboratories, with the following characteristics: • one-component product supplied ready-to-use, no catalyser or mixing are required. The product is supplied in aluminium soft-cartridges for easy application with a special extrusion gun; • thixotropic, may be applied in thick layers on both horizontal and vertical surfaces; • no expansion even when applied in thick layers, so does not alter the planarity of the steps laid; • may also be used by floor-layers allergic to epoxy and epoxy-polyurethane products; • it does not contain solvents or isocyanates; APPLICATION PROCEDURE Preparation of the substrate The substrate must be well cured, dry, flat, strong, clean and free of dust, crumbly parts and traces of oil, varnish, etc. On cementitious substrates, if the level of residual humidity is higher than the limit for laying, after curing, apply a suitable waterproofing primer such as Eco Prim PU 1K, Primer MF, Triblock P, ecc. Cementitious substrates which are not sufficiently sound and compact must be consolidated with a primer such as Eco Prim PU 1K, Primer MF, etc. On anhydrite substrates, after sanding and removing the dust, prime the surface with Primer MF or Eco Prim PU 1K. Cracks may be repaired with products such as Eporip, Eporip Turbo, etc. Excessively rough or uneven surfaces may be smoothed over with high-strength smoothing and levelling compound, such as Ultraplan, Ultraplan Eco, etc. Risers and treads on steps may be evened out using Nivorapid. When laying on top of ceramic, marble, etc., thoroughly clean and de-grease with a suitable de-waxing product before applying the adhesive.

Open the catalog to page 1

PRODUCT IDENTITY TECHNICAL DATA (typical values) Metallic substrates must be primed with Primer M; in this case, wait at least 3 hours before laying parquet. When laying on top of bonded parquet, make sure the wooden slats are well bonded to the substrate. Remove traces of varnish or wax from the surface of the floor with sandpaper down to a bare wooden surface and remove all dust with a vacuum cleaner. Application of the product and laying wood The product is supplied ready-to-use. Insert the tube in a special extrusion gun. Cut the tip off the tube, insert the extrusion nozzle and trim...

Open the catalog to page 2

the open time of the adhesive and press it against the wall. SET TO LIGHT FOOT TRAFFIC Floors may be set to light foot traffic after approximately 12 hours. Cleaning Ultrabond S997 1K may be removed from tools while still “fresh” with alcohol or a special cleaning product. Once hardened, it must be removed mechanically or with Pulicol 2000. Traces of adhesive on pre-finished, varnished parquet must be removed immediately, or at most within 4 hours, with Cleaner L. Hands may be cleaned with Cleaner H. CONSUMPTION • Laying wooden stairs: approximately 2 m² every soft cartridges (diagonal...

Open the catalog to page 3