Catalogs >
Mageba >
LASTO ® STRIP

LASTO ® STRIP
6Pages

Catalog excerpts

A tried and tested, free-moving linear bearing for the transfer of loads, movements and rotation in buildings. Typical requirements Eccentric load LASTO®STRIP linear bearings are an effective, permanent means of avoiding damage to buildings such as cracks in the structure. The high-quality EPDM elastomeric core, the special silicone grease, the low-friction, impact-resistant sliding foils and the PTFE (Teflon) coatings have been formulated to suit practical requirements and tested successfully. LASTO®STRIP linear bearings are produced entirely from high-quality materials and therefore comply with the most stringent durability and low friction requirements. The LASTO®STRIP bearing for building work provides a solution of lasting high quality for a large number of applications. Torsion Horizontal displacement Shrinkage and creep Angle of rotation Increased edge pressure Application areas Facade cracks LASTO®STRIP linear bearings are used wherever structural loads, movements and rotation have to be controlled and transmitted with a minimum of resistance. LASTO®STRIP linear bearings improve structural quality by preventing undesirable edge loads, and help to guarantee long building life. Countless buildings such as apartment blocks, houses, parking garages and shopping centres have already been equipped with LASTO®STRIP linear bearings.

Open the catalog to page 1

2 LASTO®STRIP Type NS Overlapping strip Type NS deformation bearings Type NS deformation bearings are linear bearings, with a deformable load-bearing core that renders them capable of absorbing displacement movements. They are supplied for various applied loads and permit horizontal displacements of ± 2.5mm with a bearing height of 5mm, or alternatively of ± 5.0mm with a bearing height of 10mm. These movements are absorbed by elastic deformation of the core throughout the building’s life. Central transfer of forces Adhesive tape Elastomeric load-bearing core Horizontal elastic deformation...

Open the catalog to page 2

LASTO®STRIP Type LS permanent sliding and deformation bearings are linear bearings with good deformation and sliding capability, which enables them to absorb displacements. Their sliding capability in particular enables them to absorb considerable horizontal movements (up to ± 17.5mm). Such large movements, which mainly occur during the construction phase (shrinkage, creep), are made possible by the specific design of these bearings, with their very low friction values. The independent MPA Institute in Stuttgart has carried out friction tests and confirms that the sliding friction value for...

Open the catalog to page 3

4 LASTO®STRIP Type TS Overlapping strip Type TS PTFE permanent sliding bearing LASTO®STRIP Type TS PTFE permanent sliding bearings are high-quality units for building construction, with a sliding capability that enables them to absorb positional displacements. This type of bearing is recommended when the most stringent long-term sliding-action requirements have to be satisfied. They can for example be installed without problems in buildings without heat insulation, which are permanently exposed to the full range of movement caused by temperature changes. There are two versions: the TSp...

Open the catalog to page 4

Special patterns and installation 5 Variations manufactured to special order Double-core version Various double-core versions are used for double-course masonry in building work. Variations Double core Eccentric-core version Versions with eccentric elastomeric cores are needed as a means of feeding forces in as close as possible to the load-bearing axis. Special versions for tunnels Specially produced versions with fire protection and installation straps. Version to comply with stringent fire protection regulations For use in structures to which more stringent fire protection regulations...

Open the catalog to page 5

6 Text for tenders, references Text for tenders Supply and laying without joints of deformation bearings on smooth 10-20mm mortar. Type: LASTO-STRIP NS 130 Max. permissible load: 130kN/m Deformation: ± 2.5mm Width: 150mm Supplier: mageba sa 8180 Bülach, Switzerland Tel.: +41-44-872 40 50 Fax: +41-44-872 40 59 E.mail: hochbau@mageba.ch www.mageba.ch Supply and laying without joints of permanent sliding and deformation bearings on smooth 10-20 mm mortar. Type: LASTO-STRIP LS 130 Max. permissible load : 130kN/m Displacement: ± 17.5mm Width: 150mm Supplier: mageba sa 8180 Bülach, Switzerland...

Open the catalog to page 6