LASTO ® FOL G/GE
4Pages

{{requestButtons}}

Catalog excerpts

LASTO ® FOL G/GE - 1

A foil sliding bearing for separating load-bearing elements, allowing movement without twisting Edge bonding sliding bearings are cost-efficient and easy-toinstall bearings for buildings. The bearing consists of two polyethylene sheets placed loosely one on the other. These sheets have particularly low friction and are additionally treated with silicone grease , g y on the inside, thus achieving incredibly low friction. If the bearing surfaces are very even, a simple double foil unit (Type FOL G) is sufficient. If levelling is required, an elastomer-clad double foil unit (Type FOL GE) must be used. Sliding bearing grease Pair of polyethylene sheets Elastomeric cladding Construction of LASTO®FOL GE Planar transmission of forces Horizontal sliding displacements LASTO®FOL sliding foils can be used wherever loadbearing elements must be separated, allowing for movement without twisting. Horizontal displacements between the individual construction elements are permitted with the lowest possible friction The most common friction. application is with concrete slabs which are to be placed on walls or steel girders, or which must be separated from the foundations along their whole length. These bearings are suitable for use in structural and civil engineering and in steel construction.

Open the catalog to page 1
LASTO ® FOL G/GE - 2

2 Technical Details Cross section: LASTO®FOL G without cladding Product Characteristics LASTO®FOL sliding foils offer the following advantages: • Absorb large horizontal movements • Simple to install • Extremely low friction values • High resistance to impact • Type FOL G without elastomeric cladding for smooth steel surfaces • Type FOL GE elastomeric cladding for smooth levelling of unevenness Silicon grease Edge bonding Cross section: LASTO®FOL GE with elastomeric cladding Design models mageba can provide LASTO®FOL sliding bearings in two design models: as a simple sheet unit (Type FOL G)...

Open the catalog to page 2
LASTO ® FOL G/GE - 3

Test Certificates and Installation 3 Test Certificates mageba places great importance on the high quality and durability of its products and product components. For this reason, we analyse the relevant product and performance data and these are tested and verified by recognised, independent institutes. For this product, a friction coefficient of µ = 0.03 has been calculated and confirmed by MPA Stuttgart. Sliding friction Production Lubrication: Lubrication of the sliding surfaces is performed by machine with a quality controlled silicone grease. This unique process ensures that the...

Open the catalog to page 3
LASTO ® FOL G/GE - 4

Tender Uneven surfaces: Even surfaces: Delivery and jointless installation of low-friction sliding foils on a 10-20mm grout layer. Type: LASTO-FOL G / GE Max. approved load: 10N/mm2 / 6N/mm2 Width: 150mm Supplier: mageba sa CH-8180 Bülach Tel.: +41-44-872 40 50 Fax: +41-44-872 41 29 Email: hochbau@mageba.ch www.mageba.ch Delivery and jointless installation of low-friction sliding foils on even substructure. Type: LASTO-FOL G / GE Max. approved load: 10N/mm2 / 6N/mm2 Width: 150mm Supplier: mageba sa CH-8180 Bülach Tel.: +41-44-872 40 50 Fax: +41-44-872 41 29 Email: hochbau@mageba.ch...

Open the catalog to page 4

All Mageba catalogs and technical brochures

  1. ROBO®DUR

    2 Pages

  2. SERVI-TEST

    4 Pages

  3. ROBO®SMART

    2 Pages

  4. MIGUTRANS

    56 Pages

  5. MIGUTAN

    68 Pages

  6. MIGUTEC

    72 Pages

  7. LASTO®LRB

    4 Pages

  8. RESTON®STU

    4 Pages

  9. RESTON®SDD

    2 Pages

  10. RESTON®SA

    4 Pages

  11. RESTON®PSD

    4 Pages

  12. RESTON®DISC

    4 Pages

  13. RESTON®POT

    4 Pages

  14. LASTO-HDRB

    4 Pages

Archived catalogs