product specifications RF Dimming Module with 0–10 V- Control Compatible with RA2 Select, RadioRA 2, and HomeWorks systems The RF dimming module with 0–10 V- control is a radio frequency (RF) control that operates 0–10 V- controlled fluorescent ballasts or LED drivers based on input from RA2 Select, RadioRA 2, and HomeWorks systems. • 0–10 V- control link automatically sources or sinks up to 60 mA to third-party fixtures. • Switches line voltage up to 5 A. • Configurable high- and low-end trim. • Various operating voltages available—refer to Models chart below for details on voltage requirements. • Utilizes Lutron Clear Connect RF technology—refer to Models chart below for frequency band data and Lutron system compatibility. • RadioRA 2 or HomeWorks software required for system functionality. • Mounts to an electrical junction box through a 1/2 in (21 mm) knockout opening. • Complies with requirements for use in a compartment handling environmental air (plenum) per NEC® 2011 300.22(C)(3) (LMJ- model only). Models Operating Voltage Model Number Hong Kong, Israel Compatible Systems Frequency Band RA2 Select, RadioRA 2, HomeWorks NOTE: Contact Lutron for frequency band compatibility for your geographic region if it is not indicated above. Customer Assistance: 1.844.LUTRON1 (U.S.A. / 

product specifications RF Dimming Module with 0–10 V- Control Specification Power Typical Power Consumption < 1.0 W Typical power test conditions: all loads off Regulatory Approvals cULusR, UL 2043 Plenum Rated, FCC Approved. Complies with the limits for a Class B device, pursuant to Part 15 of the FCC rules: IC, NOM, ANATEL (LMJ- model) CE, TRA, CITC (LMK- model) WPC (LMN- model) Ambient operating temperature: 32 °F to 104 °F (0 °C to 40 °C) Ambient operating humidity: 0% to 90% humidity, non-condensing. Indoor use only. Operates using Clear Connect RF technology for reliable wireless communication;...

product specifications RF Dimming Module with 0–10 V- Control Dimensions Dimensions are shown as: in (mm) 1/2 in (21 mm) knockout opening Dimensions for all models. Model LMJ-5T-DV-B shown. Customer Assistance: 1.844.LUTRON1 (U.S.A. / Canada) +44.(0)20.7680.4481 (Euro

product specifications RF Dimming Module with 0–10 V- Control Wiring Schematics LMJ- and LMQ- models: Use the supplied conduit nut and wire the module as shown. 120 / 277 V~ 50 / 60 Hz (LMJ- model) 220–240 V~ 50 / 60 Hz (LMQ- model) Junction Box1 Line / Hot Switched Hot Neutral To Fluorescent Ballasts / LED Drivers 1/2 in (21 mm) Knockout Opening Conduit Nut S ome applications (in the U.S.A.) require the RF module to be installed inside an additional junction box. For information about how to perform this installation see Application Note #423 (P/N 048423) at www.lutron.com Please consult all...

product specifications RF Dimming Module with 0–10 V- Control Wiring Schematics (continued) LMK-, LMM-, and LMN- models: 220–240 V~ 50 / 60 Hz Junction Box1 Line / Hot Neutral Switched Hot To Fluorescent Ballasts / LED Drivers 0–10 V- to Fluorescent Ballasts / LED Drivers Conduit Nut R F module can be installed in a junction box or marshalling box. Please consult all local and national electric codes for proper installation methods. Customer Assistance: 1.844.LUTRON1 (U.S.A. / Canada) +4

product specifications RF Dimming Module with 0–10 V- Control Communications Wired and RF Configuration (RadioRA 2 and HomeWorks) Repeater * RF Dimming Module 30 ft (9 m) maximum Hybrid Repeater Hybrid Repeater Power Repeater Link Communication Wired Power Repeater Link Power Repeater Link 9V Hybrid Repeater 30 ft (9 m) maximum RF Link 1000 ft (305 m) maximum wire length per run RF Link 1000 ft (305 m) maximum wire length per run * n HomeWorks systems, use Hybrid Repeaters for range extension. In RadioRA 2, the repeater shown may be either a main repeater I (1 required) or auxiliary repeater...