Fluidised hydraulic binder for structural, crack-resistant screeds with high mechanical strength, normal setting time and rapid drying Product description Fluidised hydraulic binder to be mixed with assorted aggregates with a particle size range of 0 to 8 mm and water to produce high-strength, crack-resistant structural screeds with normal setting time and rapid drying, suitable for laying porcelain stoneware, ceramic tiles, natural stone, parquet, microcement, resins and resilient floor coverings of any type and format. Shrinkage-resistant, suitable for underfloor heating and for the installation of floating or bonded screeds in both indoor and outdoor areas; ideal for the rapid subsequent laying of ceramic tiles after 24 hours, natural stone after 2 days, and parquet, PVC, linoleum and carpet after 14 days. Creation of screeds incorporating underfloor heating coils without the need for fluidising additives. Excellent workability, even when applied using a pressure pump. Certifications EC1 Plus Gev Emicode EPD Environmental Product Declaration LCA results for Global Warming Potential - Greenhouse Gases (GWP-GHG) Impact category Unit A1-A3 C1 C2 C3 C4 D 1 - X-Floor® Technical Specifications

Screeds Self-levelling compounds Levelling Compounds Existing tiles Radiant heating systems Concrete and reinforced concrete Fibre-cement sheets Lightweight panels Interior – exterior Floors Overlay Terraces and balconies SPA and Hammam Indoor wet areas (bathrooms, showers) Industrial flooring Creation of floating or bonded screeds in both indoor and outdoor areas, ideal for rapid subsequent installation. Residential, public and commercial construction The ambient and surface temperature must be above 5°C at the time of installation and for 12 hours after application Do not apply to wet surfaces,...

Mixing ratio Consistency of the mix Mixing time pH of the mixture Specific gravity of the mixture Pot life Applicable thicknesses Applicable thicknesses Applicable thicknesses Application Permissible application temperatures Ready for foot traffic Drying time before laying ceramic tiles Drying time before laying natural stone Waiting time before laying resilient flooring Operating temperature 20 kg (1 bag) - 0/8 mm gravel 135-170 kg - Water < 10 l (depending on the moisture content of the aggregates) Damp ground 5-10 minutes Floating or decoupled screeds: 40 to 80 mm Metal straight edge and trowel...

The mix can be prepared using a site-based concrete mixer, a horizontal screw mixer or an automatic pressure pump such as the Turbosol. Manual mixing with a trowel is not recommended as it does not allow for proper homogenisation of the mixture. Mix thoroughly for at least 5–10 minutes. Water must be added with particular care to achieve a mixture with the consistency of ‘damp, almost plastic earth’, which must not allow surface water to rise to the surface during the compaction and trowelling stages. Mixing ratio: X-Floor 20 kg (1 bag) – 0/8 mm gravel 170–210 kg – Water < 10 l (depending on...

throughout the full thickness of the screed, acting as a levelling layer and as a vapour barrier against any rising damp. Screeds incorporating heating and cooling coils These are floating screeds in which the heating and cooling system coils are embedded within the screed thickness. The thickness of the screed above the system pipes must be ≥ 30 mm. Before laying ceramic tiles, natural stone, parquet, etc., the system must undergo the start-up cycle in accordance with the provisions of standard UNI EN 1264-4. Floating screeds on a layer of acoustic or thermal insulation In this case, thicknesses...

Flooring installation The application of finishes may be carried out at least 12 hours after the final coat under standard conditions. The installation of ceramic tiles, natural stone or mosaics shall be carried out using high-performance gels based on Litokol technology, which guarantee complete force transfer, consistent system performance and total safety. To ensure perfect adhesion of the adhesive gel, apply a thin, even coat of the mixture using the smooth side of the trowel and, immediately afterwards, apply the desired thickness using the notched side. In accordance with the UNI 11493-1...

Powered by TCPDF (www.tcpdf.org) guidelines which do not in any way bind our Company. We therefore recommend carrying out a preliminary test to verify the product’s suitability for the intended use; in any case, anyone intending to use it is required to determine whether or not it is suitable for the intended use and, in any event, assumes all liability that may arise from its use. Always refer to the latest updated version of the Technical Data Sheet, available on the website www.litokol.com Specification item The screed will be laid using an X-Floor-type hydraulic mineral binder, suitable for...