Catalogs >
LITOKOL >
TDP - TDF

TDP - TDF
1 / 1Pages

Catalog excerpts

Technical Datasheet - Metal Trim Aluminium Square Trim - TDP/TDF Product Description A revolutionary and versatile profile. An alternative to an ordinary straight edge or L angle Aluminium Profile, the TDP offers a more luxurious finish to any edge. It can be used as an edge trim on the vertical with wall tiles or on the horizontal with Floor tiles or even as a feature strip in wall or floor applications. The extruded Aluminium profile gives a square appearance when installed and is also available with internal and external corner pieces (EDP) to obviate sharp edges when mitring is necessary. The TDF profile is a formable version of the TDP allowing a curved radius to be achieved in installations. Dimensions and Colour All TDF and TDP profiles are available in 2.5m lengths in varying depths and finishes - see the Metals colour chart for depth/finish combinations. Available in 6mm, 8mm, 10mm, 12mm and 15mm depending on profile. Technical Details Profiles are available in different anodised finishes and powder coated finishes - All natural Aluminium (Mill Finish) has a oxide film of approx 0.2 microns, when Mechanically and Chemically polished the anodising process increases this to 5 microns, up-to 20 for the Matt finish and 100 for Powder coated. Allied Products: TDP / TDF has specially designed aluminium corner pieces EDP. They provide perfect corners with no sharp edges where mitering of the profile is required. Available in 6mm, 8mm, 10mm and 12mm depths. Genesis TDP/TDF does not require any special maintenance. Oxidation films on Aluminium may be removed with a common polishing agent; however, they do reoccur. Damaged anodised finishes may only be repaired by recoating. 1. Select TDF/TDP according to tile thickness. Aluminium must be tested to verify its suitability if chemical stresses are anticipated. Cementitious materials, in conjunction with moisture, become alkaline. Since aluminium is sensitive to alkaline substances, exposure to the alkali (depending on the concentration and time of exposure) may result in corrosion (aluminium hydroxide formation). Therefore, it is important to remove adhesive or grout residue from visible surfaces. In addition, ensure that the profile is solidly embedded in the setting material and that all cavities are filled to prevent the collection of alkaline water. The anodised layer creates a finish that retains a uniform appearance during normal use. The surface, however, is susceptible to scratching and wear and may be damaged by tile adhesive, mortar, or grouting material. Therefore, setting materials must be removed immediately. Otherwise, the description regarding aluminium applies. 2. Trowel tile adhesive over the area that forms the perimeter of the tiled covering. 3. Press the perforated anchoring leg of the profile into the tile adhesive and align, mechanical fix if required 4. Trowel additional adhesive over the perforated anchoring leg to ensure full coverage. 5. Solidly embed the tiles so that the tiled surface is flush with the top of the profile, the profile should not be higher than the tiled surface. 6. Fill the joint completely with grout. Aluminium AA 6063 T6 / UNS A96063 anodised to DIN 17611 Si% 0.2-0.6 Fe% 0.35 Cu% 0.1 Mn% 0.1 Mg% 0.45-0.9 Zn% 0.1 Ti% 0.1 Cr% 0.1 Al Balance P.V.C. Trim • Stair Nosings • Movement Joints • Transitions • Entrance Matting• Edge Protection • Metal Profiles • Tactiles• Tools Litokol spa - via G. Falcone, 13/1 - Rubiera (RE) - Italy Tel.+39.0522.622811- info@litokol.it - w

Open the catalog to page 1

TDP - TDF 1 / 1Pages

Catalog excerpts

All LITOKOL catalogs and technical brochures

TDP - TDF
1 / 1Pages