Wall & Floor READY-TO-USE WATER-BASED DECORATIVE SYSTEM FOR WALLS. SUITABLE FOR OVERLAYING. FOR INTERIORS. PRODUCT WITH VERY LOW VOLATILE ORGANIC COMPOUND EMISSION RATE. Synthetic resin-based decorative system in aqueous dispersion, ready to use with a strong texture and saturated colours. Allows the creation of a spatula effect textured surface with even colour. ADVANTAGES / FEATURES • Product with very low volatile organic compound (VOC) emission rate, compliant with class A+ (Émission dans l’air intérieur – French Regulations) • Water-based product • Easy to sand • Product with excellent fluidity and easy to spread • Product exempt from restrictions for road, sea, air and rail transport • Available in the 27 nuances designed by Rinaldo Rinaldi for the Spaziocontinuo® palette, and on request in any colour of the international NCS and RAL colour charts • Ready-to-use product • The system can be applied to a broad range of substrates and also overlaid on existing coverings • Allows the creation of even-coloured surfaces with a spatula effect and textured look • Sanding not required • Extremely economical decorative system due to high product yield • Compliant with harmonised European standard UNI EN 15824 Intended uses Interiors Walls Overlaying on existing coverings in ceramic, porcelain stoneware, mosaic, agglomerates, natural stones Covering of furniture and structures in wood, metal or plastic Residential, public, commercial building Indoor wet areas (bathrooms, shower enclosures) DECORATIVE SYSTEM PLANNING The only way to guarantee the long-lasting performance of resin decorative systems is to properly plan the process. It is therefore advisable to consult the national regulations in force in each country, for example standard UNI 10966 for Italy, which defines the planning and installation criteria for resinous systems for interior and exterior horizontal and vertical surfaces. Some of the general precautions that need to be followed are listed below as an example. Suitable substrates RasanteParete/Ceramica EVO on: Rough cement plaster Washable paints (temperas need to be removed) Skim coats Cement plasters with fine mortar finish Gypsum-based plasters or smoothers Underfloor heating systems Smooth cement panels Normal and waterproof gypsum Fibre cement slabs (such as Aquapanel) Existing coverings in ceramic, porcelain stoneware, mosaic and natural stone Lightweight panels (such as WED

ANALYSIS OF SUBSTRATE Curing In order to be considered dimensionally stable, a substrate must be sufficiently cured. Indicatively speaking, cement screeds or plasters need about 7 days per centimetre of thickness, and ready-mixed products depend on the manufacturer’s instructions. Integrity and compactness Assessed by visual inspection. Plastering must be consistent and compact for its entire thickness. There must not be any cracks or fissures on the substrate; in this case, it is advisable to reinforce the surface by embedding a reinforcing mesh in the substrate leveller. Brittle or flaking...

correctly. - in case of slight rising damp, Osmogrout, an osmotic waterproofing membrane, must be applied before the entire decorative system. - use strictly Hydrolux EVO as the topcoat (two-component, water-based topcoat), to be applied in three coats over the last textured coat. - take extra caution near plumbing pipes and fittings; these are critical points from which water may infiltrate under the resin system. Hydrolux EVO must therefore be applied in contact with the piping; moreover, before installing the taps and fittings, apply the MS-polymer grout Litosil MS in abundance around the...

Powered by TCPDF (www.tcpdf.org) COLOUR CHART Data detection at temperature +23 °C, R.H. 50% and with no wind. May vary depending on the specific conditions of the installation site. The different textures of the Spaziocontinuo® surfaces have different colours, saturation and brightness. For each project, use materials from a single production batch. Materials from different batches may assume slightly different colours. The texture of Spaziocontinuo® is characterised by material discontinuity and natural irregularity, achieved through the skilful artisan work of the installer, thus making the...