SpazioLamina EVO #Crudo Wall & Floor THREE-COMPONENT DECORATIVE RESIN FOR FLOORS AND WALLS. SUITABLE FOR OVERLAYING AND UNDERFLOOR HEATING. FOR INTERIORS. PRODUCT WITH VERY LOW VOLATILE ORGANIC COMPOUND EMISSION RATE. SpazioLamina EVO #Crudo is a flexible, water-based epoxy decorative system characterised by metallic textures with a high visual and tactile impact. The shiny metallic reflections create energetic and shimmering surfaces. ADVANTAGES / FEATURES • Product with very low volatile organic compound (VOC) emission rate, compliant with class A+ (Émission dans l’air intérieur – French Regulations) • Suitable for installation on heating screeds • Suitable for overlaying on existing flooring • Extended workability of mix (about 40 minutes), which facilitates application on large surfaces • Product exempt from restrictions for road, sea, air and rail transport • Water-based product • Product with excellent fluidity and easy to spread • Easy to sand • Smooth surface with metallic effect • Excellent resistance to wear • Available in four different colours obtained using genuine metallic powders: Steel, Bronze, Brass, and Copper Steel, Brass, and Copper Bucket part A: 2.00 kg + Can part B: 0.46 kg + Can part C: 1.10 kg) = Total 3.56 kg Steel Bucket part A: 2.00 kg + Can part B: 0.46 kg + Can part C: 1.70 kg) = Total 4.16 kg Intended uses Interiors Floors and walls Underfloor heating Overlaying on existing floors and coverings in ceramic, porcelain stoneware, mosaics, agglomerates, natural stones Residential, public, commercial building Indoor wet areas (bathrooms, shower enclosures) Covering of furniture and structures in wood, metal or plastic Suitable substrates - Multifondo EVO on: Cement screeds Self-levellers Skim coats Lightweight panels (such as WEDI-SCHLUETER). Separation membrane Underfloor heating systems Concrete Normal and waterproof gypsum Fibre cement slabs (such as Aquapanel) Gypsum and anhydrite Existing floors and coverings in ceramic, porcelain stoneware, mosaics, agglomerates, natural stones and wood Rough cement plaster Wood panels Metal Smooth

RESIN DECORATIVE SYSTEM PLANNING The only way to guarantee the long-lasting performance of resin decorative systems is to properly plan the process. It is therefore advisable to consult the national regulations in force in each country, for example standard UNI 10966 for Italy, which defines the planning and installation criteria for resinous systems for interior and exterior horizontal and vertical surfaces. Some of the general precautions that need to be followed are listed below as an example. ANALYSIS OF SUBSTRATE Vapour barrier/retarder Make sure the vapour barrier or retarder has been properly...

Steel, Brass, and Copper Component A 56.2 parts by weight – Component B 12.9 parts by weight – Component C 30.9 parts by weight. Steel Component A 48.1 parts by weight – Component B 11.1 parts by weight – Component C 40.8 parts by weight. The three components are pre-batched in their respective packaging. Pour all of component B into the container of component A, and mix until completely homogenised. Delicately pour into the mix the pre-batched powder component C, mixing slowly and incorporating it consistently. Mix, preferably using an electric drill with mixing paddle at low speed (≈ 300/min.)...

Shower enclosure and areas in direct contact with water Each time the decorative system is applied in a wet environment, certain precautions are necessary: - If covering a niche inside a shower enclosure, check that the slope is sufficient to prevent any water build-up. - if there is a pre-existing waterproofing system, check that it is cementitious (e.g. Coverflex and Elastocem), applied with a smooth trowel (do not apply on ready-to-use and/or roller-applied waterproofing systems); in any case, a waterproofing system is not necessary insofar as this function is performed by these resin systems,...

Powered by TCPDF (www.tcpdf.org) Data detection at temperature +23 °C, R.H. 50% and with no wind. May vary depending on the specific conditions of the installation site. The different textures of the Spaziocontinuo® surfaces have different colours, saturation and brightness. For each project, use materials from a single production batch. Materials from different batches may assume slightly different colours. The texture of Spaziocontinuo® is characterised by material discontinuity and natural irregularity, achieved through the skilful artisan work of the installer, thus making the surfaces unique....