Ottoseal S34 SINGLE-COMPONENT SILICONE-BASED, NEUTRAL CROSS-LINKING GROUT. FOR INTERIORS AND EXTERIORS. IDEAL FOR INDUSTRIAL USE. CERTIFIED ACCORDING TO ISEGA FOR CONTACT WITH FOODSTUFFS. Single-component silicone- and oxime-based, neutral cross-linking grout, free from methylethyl ketone oxime. It may be used in areas with high chemical stress. Does not cause corrosion (rust) on unprotected metal surfaces. ADVANTAGES / FEATURES • Product with very low volatile organic compound (VOC) emission rate, compliant with class A+ (Émission dans l’air intérieur – French Regulations) • Non-corrosive • Excellent resistance to temperatures up to + 510 °F • Very high mechanical strength, resistance to cuts and tears • Flexibility • Suitable for surfaces subject to vehicle traffic (e.g. Forklifts) and resistant to mechanical cleaning with pressure washers • Ready to use • No restrictions for transport over road, sea, air and rail • Excellent resistance to weathering, aging and UV rays 10.4 U.S. oz. (310 ml) cartridge (boxes with 20 pcs) Sealing of floor joints and connection joints subject to heavy chemical loads, e.g. in dairies, slaughterhouses, food and beverage production facilities, canteen kitchens, etc. Sealing of floors and connection joints subject to heavy mechanical loads, e.g. premises intended for warehouse and production purposes, work site areas, parking garages, underground car parks, car repair shops, car washes, etc. The surfaces to be grouted or bonded must be perfectly clean, dry and free of dust, grease, oil and old paint. Cleaning non-porous surfaces: clean with OTTO Cleaner T (drying time about 1 minute) and a dry fiber-free cloth. Cleaning porous surfaces: clean the surfaces mechanically, e..g with a steel brush or a smoothing disc to remove loose particles. Remove the top part of the threaded part of the cartridge, screw in the plastic nozzle and cut it to the right angle depending on the desired diameter and profile. Insert the cartridge in a manual or air gun (with telescopic piston) and extrude the adhesive grout, being careful to avoid the entrainment of air. Once opened, the packages must be used in a relatively short time. The ideal operating temperature for the substrate and grout is between 59°F (15°C) and 77°F (25°C). The joints must be finished within the grout open time. Avoid contact with solvents during cross-linking. given the large number of factors which influence the treatment and the application of the product, the user should always perform a test treatment and application.

• Spread the product at temperatures between 40°F and 95°F • In warm climates, keep the packaged product in a cool and dry place away from the sun before use • Prima di applicare il prodotto è necessario assicurarsi che i materiali costruttivi con i quali si verrà a contatto siano compatibili con il prodotto stesso e tra loro e che non possano danneggiare o alterare le caratteristiche del prodotto • In the case of construction materials that will subsequently be worked at the point where the product has been applied, the user must verify that the solid or volatile components to be used does compromise...

IDENTIFICATION DATA Polymerization Consistency of mix Specific gravity Film-forming time Setting in 24 hours Acceptable application temperatures Recommended application temperatures Serviceability Temperatures Set to light foot traffic Ready for use APPLICATION DATA Appearance Colors Customs code Shelf life Thick colored paste See color chart 32149000 12 months in original packaging away from sources of heat and direct sunlight. Protect against frost. Set to thickness Shore hardness A Elastic modulus at 100% Elongation at break Tensile strength Overall deformation allowed Class Application rate...

Powered by TCPDF (www.tcpdf.org) Nitro thinner KEY RESISTANT RESISTANT UP TO 72 HOURS NON-RESISTANT COLOR TABLE Data detection at temperature +73.4°F (+23 °C ), R.H. 50% and with no wind. May vary depending on the specific conditions of the installation site. Form n. 810 Revision n. 0 Date: March 2021 The information and provisions contained in this technical data sheet reflect our best experience. Given the impossibility of directly intervening on the conditions of the work site and execution of the works, they represent indications of a general nature, which are in no way binding on our Company....