Litoacril LA201 READY-TO-USE ADHESIVE IN DISPERSION WITH NO VERTICAL SLIP AND LONG OPEN TIME FOR THE INSTALLATION OF CERAMIC AND PORCELAIN TILES ON INTERIOR WALLS AND FLOORS. Ready-to-use adhesive in dispersion made from synthetic resins in aqueous emulsion, selected aggregates and organic additives. ADVANTAGES / FEATURES 11lb (5 kg) buckets - 1,929lb (875 kg) standard pallet (175 buckets) 22lb (10 kg) buckets - 1,587.3lb (720 kg) standard pallet (72 buckets) 55.1 lb (25 kg) buckets - 1,058.2lb (750 kg) standard pallet (30 buckets) Intended uses Interiors Floors and walls Ceilings Residential, public, commercial building For example, it can also be used to install suitable materials in the following areas: Interior floors in residential and public/commercial settings (pedestrian areas) Substrates Longest allowable tile side (in) (cm) Cement or Litocem/Litocem Pronto-based non-heating screeds up to 30 Cement or Litocem/Litocem Pronto-based heating screeds up to 30 Sulfate-based (anhydrite) non-heating screeds up to 30 Sulfate-based (anhydrite) heating screeds up to 30 Interior walls in residential, public/commercial and industrial settings Substrates Longest allowable tile side (in) (cm) Lime/cement plaster up to 45 Gypsum-based plaster up to 45 Cast-in-place concrete (2) up to 30 Pre-cast concrete up to 30 Fiber cement and cement panels up to 45 Gypsum slabs up to 45 Allows the installation of ceramic, porcelain and mosaic wall coverings without the need for plastic spacers Bonding on all types of ceramic, porcelain and mosaic tiles, in interiors on floors and walls Ideal for application on gypsum-based plasters with no need to apply a primer beforehand No restrictions for transport over road, sea, air and rail Materials Ceramic and porcelain tiles Ceramic mosaics Single fired Double fired Terracotta - Clinker Marble – Granite – Stone Natural stones Insulating panels Polystyrene panels Soundproof panels Glass wool Rockwool Cork Porcelain stoneware Suitable substrates Cement screeds Self-levelers Skim coats Gypsum and anhydrite Gypsum Plasters Insulating panels Lightweight panels Fiber cement slabs Aerated concrete

(1) After treatment with Primer C or Primer X94. Maximum humidity = 0.5%. (2) Curing time: minimum 6 months. (3) After cleaning and degreasing with Litoscrub EVO. (4) After treatment with the adhesion promoter Prepara Fondo EVO. (5) After treatment with Primer C or Primer X94 for non-waterproof gypsum. (6) After treatment with Primer X94. INSTALLATION PLANNING The only way to guarantee the long-lasting performance of ceramic and porcelain tile installations is to properly plan the process. It is therefore advisable to consult the national regulations in force in each country, for example standard...

Marble, natural and recomposed stones Materials subject to deformation or stains due to water absorption require a quick-setting (C2F) or reactive (R2) adhesive. Marble and natural stones, even if similar in nature, may have different characteristics. In case of doubt, contact the Litokol S.p.A. Technical Help Service for detailed information or to perform a laboratory test. Natural stone slabs with reinforced backing (resin, mesh, etc.) or specific treatments (for example anti-rising damp, etc.), unless otherwise prescribed by the manufacturer must be tested for compatibility with the adhesive....

Powered by TCPDF (www.tcpdf.org) Waiting time for grouting Set to light foot traffic Ready for use Serviceability Temperatures How to clean equipment Consumption Consumption Consumption Consumption Wall: 6-8 hours – Floor: 24 hours 24 hours 7 days From -22°F to +194°F (-30°C to +90°C) With water when product is fresh. Mechanically when product has set. 3.5 mm (0.14in) trowel: 1.5 kg/m2 (3.3lb/yd2) 1/4" (6 mm) trowel: ft2 per 44 lb (20 kg) bag 85-90 (2.5 kg/m2) 1/4" (6 mm) trowel: ft2 per 44 lb (20 kg) bag 70-75 (3 kg/m2) 3/8" (10 mm) trowel: 60-65 ft2 per 44 lb (20 kg) bag (3.5 kg/m2) Standard...