Latexkol ELASTICIZING SYNTHETIC LATEX FOR CEMENTITIOUS ADHESIVES. SUITABLE FOR UNDERFLOOR HEATING. FOR INTERIORS AND EXTERIORS. PRODUCT WITH LOW VOLATILE ORGANIC COMPOUND EMISSION RATE. Synthetic, highly elastic latex in aqueous dispersion based on acrylic polymers. ADVANTAGES / FEATURES • Product with very low volatile organic compound (VOC) emission rate, compliant with class A+ (Émission dans l’air intérieur – French Regulations) • Suitable for installation on heating screeds • Plastic and fluid mix 5 kg (11lb) cans - 600 kg (1,322.7lb) standard pallet 10 kg (22lb) (cans - 600 kg (1,322.7lb) standard pallet 20 kg (44lb) cans - 720 kg (1,587.3lb) standard pallet Liquid additive to be mixed with cementitious adhesives in class C1 (see Litokol K17/K18 data sheet) in partial or total replacement of water. Use of the additive gives the adhesive high deformability and improves its performance, making it suitable for more intense applications (see synoptic table). Adhesives C1 44lb (20 kg) (1 bag) Litokol K17 4.8 l (1.27US gal lqd) of water 44lb (20 kg) (1 bag) Litokol K18 4.8 l (1.27US gal lqd) of water Pour the right quantity of liquid, depending on the application, into a clean container and slowly add the powder, stirring with an electric drill with mixing paddle until a consistent mix is obtained without lumps. Let the mix rest for about 5 minutes and then briefly mix again for a few seconds. Do not add more liquid to the mix once setting has begun. Hand mixing is not recommended. Spread the mix onto the substrate using the smooth part of the trowel to create a layer approximately 1 mm thick (0.039in). Immediately afterwards, apply the product using the notched part of the trowel. The trowel notch size will depend on the size of the tiles. A back coverage of 65-70% of slabs is nonetheless required for interior installations, and 100% of slabs for exterior installations or floors subject to heavy traffic. In exterior installations or areas subject to high stress, the adhesive should also be applied to the back of the slabs (back-buttering method). The tiles must be laid on the adhesive when fresh, firmly pressed to ensure good contact. The product's open time in normal temperature and humidity conditions is approximately 10 minutes. High temperatures will shorten it, low temperatures will lengthen it. Very warm or windy climates, or particularly absorbent substrates may drastically reduce it to a few minutes. It is therefore recommended to regularly check that the adhesive has not skinned over. If it has skinned over, the adhesive will need to be combed again using the notched trowel. The tiles must be installed with joint widths suitable for their size. Special Products C2 S1 3.17 qls. (3.0 l)of water + 6.6lb (3.o kg) of Latexkol 3.17 qls. (3.0 l)of water + 6.6lb (3.o kg) of Latexkol

Take account of any expansion, perimeter, divider or structural joints. Leave a space of at least 1/5" (5 mm) near walls or any surface elevations. The tiled surface must be protected for at least 24 hours against any rain wash, and for approximately 5-7 days against any frost and direct sunlight. Joints can be grouted after approximately 6-8 hours in the case of wall tiles and after 24 hours in the case of floor tiles. For grouting, it is possible to use the cementitious grouts Stylegrout 0-8, Stylegrout 3-20, Stylegrout Tech or the ready-to-use polymer mortar FillGood EVO, or, for grouting...

≥ 72 psi (0.5 N/mm2) after 20 minutes EN 1346 ≥ 1/5" (5 mm) EN 12002 Excellent Excellent Low Open time Transverse deformation Resistance to alkalis Resistance to solvents Resistance to acids Synoptic table Possible Applications Substrates INTERIOR FLOORS Unbonded or floating cured cement screeds Dried, sanded anhydrite-based screeds primed with Primer C or Primer X94 Existing floors in cement, clean and degreased Existing floors in ceramic, stone, agglomerates, clean and degreased Cement heating screed after pre-heating cycle Surfaces treated with Hidroflex Concrete structures cured for at least...

Powered by TCPDF (www.tcpdf.org) Form n. 500 Revision n. 1 Date: January 2021 The information and provisions contained in this technical data sheet reflect our best experience. Given the impossibility of directly intervening on the conditions of the work site and execution of the works, they represent indications of a general nature, which are in no way binding on our Company. It is therefore advisable to perform a spot test to check the suitability of the product for the intended use. In any case, users must determine whether or not it is suitable for the intended use and shall assume all associated...