Idrostuk LIQUID ADDITIVE IN AQUEOUS DISPERSION FOR CEMENTITIOUS GROUTS. SUITABLE FOR UNDERFLOOR HEATING. FOR INTERIORS AND EXTERIORS. PRODUCT WITH LOW VOLATILE ORGANIC COMPOUND EMISSION RATE. Synthetic latex in aqueous dispersion. ADVANTAGES / FEATURES • Product with low volatile organic compound emission rate, compliant with Class A+ according to French Regulations • Suitable for installation on heating screeds • Plastic and fluid thixotropic mix • High abrasion resistance • Water-repellent • Stable and consistent colors 2 l (0.528US gal lqd) cans - 500 kg (1,102.3lb) standard pallet 5 l (1.32US gal lqd) cans - 600 kg (1,322.7lb) standard pallet 10 l (2.64US gal lqd) cans - 600 kg (1,322.7lb) standard pallet 20 l (5.28US gal lqd) cans - 720 kg (1,587.3lb) standard pallet Liquid additive to be mixed with cementitious grouts in the Stylegrout line in partial or total replacement of water. Use of the additive improves the final properties of the grouting. In particular, adhesion to tile sides and abrasion resistance is improved, while water absorption and porosity is reduced. Suitable therefore for applications on tiled surfaces subject to high physical and mechanical stress, such as: terraces, balconies, swimming pools, industrial floors, gypsum board paneling, etc. The product can be used with any colored cementitious grout without any significant color alterations. PRELIMINARY CHECKS AND JOINT PREPARATION The substrates must be clean, solid, compact, crack-free, properly cured and without rising damp. Check that the adhesive or mortar used for tile bonding is completely set and dry. The joints must be clean, free from dust and empty for the entire depth of the tiles. Any traces of adhesive or mortar spilled back into the joints must be removed. When grouting very absorbent tiles and in the presence of very warm climates, the joints will need to be dampened with a sponge soaked with water. Make sure that the ceramic and porcelain tiles can easily be cleaned and their surface is not absorbent. Certain types of tiles (e.g., polished porcelain stoneware) or natural stones have micro-porosities and surface roughness that can cause surface staining and make cleaning very difficult. Spot tests should always be performed. Special Products StyleGrout 0-8 0.24US gal (0.9 l) of Idrostuk 5.9 - 6.3 qts. (5.6 - 6.0 l) of Idrostuk StyleGrout 3-20 0.16US gal (0.6 l) of Idrostuk 3.8-4.2 qls. (3.6-4.0 l) of Idrostuk

Pour the right quantity of liquid, depending on the application, into a clean container and slowly add the powder, stirring with an electric drill with mixing paddle until a consistent mix is obtained without lumps. Let the mix rest for about 5 minutes and then briefly mix again for a few seconds. The pot life is about 40 minutes at a temperature of 73.4°F (+23°C), therefore it is advisable to mix only the quantity of material that can be applied within this period of time. Do not add more liquid to the mix once setting has begun. Hand mixing is not recommended. Apply the mix in the joints using...

IDENTIFICATION DATA Appearance Color Customs code Shelf life Liquid White 39069000 24 months in original packaging in a dry place. Protect against frost. APPLICATION DATA Mix ratio Consistency of mix Mix curing time Brookfield viscosity (sp 6 - 20 rpm) pH of mix Specific gravity of mix Pot life Joint width Application Acceptable application temperatures Waiting time for cleaning Set to light foot traffic Ready for use Serviceability Temperatures How to clean equipment Consumption According to use Creamy thixotropic mortar 5 minutes 10 - 30 mPa^s (24.19 - 72.57 lb/ft-h) 10 - 12 According to use...

Powered by TCPDF (www.tcpdf.org) Form n. 501 Revision n. 4 Date: January 2021 The information and provisions contained in this technical data sheet reflect our best experience. Given the impossibility of directly intervening on the conditions of the work site and execution of the works, they represent indications of a general nature, which are in no way binding on our Company. It is therefore advisable to perform a spot test to check the suitability of the product for the intended use. In any case, users must determine whether or not it is suitable for the intended use and shall assume all associated...