fluobus
12Pages

Litelab’s FluoBus product line is ideal for architectural lighting designs that require a combination of fluorescent and task lighting. FluoBus combines Litelab’s unique BusRun busway track lighting with a T5 fluorescent up or downlight component, in an attractive suspended extrusion system. 2 FluoBus BusRun T5 fluorescent up/downlight

The PACE Gallery located in the 798 Arts District of Bejing relies on FluoBus to light their collection and provide general uplighting in the gallery spaces. The system is designed to work just like a track system with starters at both ends – one for the uplight and one for the downlight. The various section lengths are designed around T5 lamp lengths. However, the system may be modified in length to fit the architecture of the space. While the bus component of the system was designed FluoBus may be configured as a single lighting component up to with Litelab’s Jewelers Collection in mind,...

fluobus: mounting options Ceiling Mounted Pendant FluoBus is supported with 1/2” [12mm] conduits and finished at the ceiling plane with a 5” [127mm] diameter canopy. The image shown above details the FluoBus FB configuration (shown on the right page.) This option provides uplighting from T5 fluorescent fixtures and task lighting from adjustable Par fixtures that plug into the lower BusRun channel. Mounting height 18” [457mm] standard for pendant. Ceiling Mounted Level Glide Level glides are available for 20amp configurations and finished at the ceiling plane with a 5” diameter canopy. Wall...

fluobus: configurations One circuit BusRun (Two circuit BusRun is available.) T5 fluorescent fixture in the upper channel and BusRun in the lower channel. BusRun in the upper channel and T5 fluorescent fixture in the lower channel. T5 fluorescent fixtures located in both channels. BusRun located in both channels.

fluobus: pendant spacing The system is designed to work just like a track system with starters at both ends – one for the uplight and one for the downlight. The various section lengths are designed around T5 lamp lengths, however the system may be modified in length to fit the architecture of the space. Straight runs of FluoBus, as shown below, are constructed from starters and joiners. Electrical connection Electrical connection End pendants inset 1”[25mm] to center Must be supported at each joint. elevation of linear run - pendant/cable SINGLE (SI) Electrical connection Electrical...

fluobus: wall mounted spacing The wall-mount system, like the hanging system, is built using starters and joiners, with the exception that the feeds run through an armature that attaches to the wall of the FluoBus. When installed, the FluoBus system mounts 6” [152mm] from the wall surface. Ballast placement is under the fixture so the fluorescents butt end-to-end for a “no dark spots” appearance. Electrical feed Electrical feed End wall-mount brackets inset 2.5”[64mm] to center Must be supported at each joint. plan of linear run - wall-mount Electrical feed Electrical feed 6” [152mm] from...

fluobus: FB standard “stand alone” options fluobus: luminaire options FluoBus utilizes T5 fluorescent fixtures in 3’ [849mm] and 4’ [1149mm] combinations based on the length of the single unit. The chart below details the combinations. The fixtures accept either standard output (SO) or high output (HO) fluorescent lamps. Note that stand alone units are slightly longer to accommodate the hanging hardware. A complete line of LED, halogen and metal halide fixtures are available at www.litelab.com. fluobus: mounting options fluobus: voltage options 10 FluoBus can be specified in 1 circuit for...

fluobus: accessories To control and direct the fluorescent light, Litelab offers a range of lens and louvers as shown below. To provide a finished look to the lower channel, coverplates that accept stem fixtures and clip into the extrusion are available in matching finishes to the FluoBus housing. These coverplates can be combined with the fluorescent fixtures and accessories in the lower channel. Top Lens Option Available: Frosted Coverplate/Fixture Option Bottom Lens Option Available: Frosted, White Linear or Prismatic Bottom Louver Option

fluobus: system specifications FluoBus is a combination fluorescent/bus–uplight/downlight–lighting system composed of an aluminum extruded housing 5.5”x 1.75” [140mm x 45mm] and finished in a durable powder coat paint or a natural brushed finish. The extrusion contains an upper and lower channel that accepts T5 fluorescent fixtures and BusRun Busway. The fluorescent fixtures and bus are interchangeable in upper and lower channels or may be used exclusively in one or both. Both the fluorescent and bus are available in 120/230 volt and in 16, 20, 30 or 60 amps per circuit depending on the...

FB Fluorescent [upper] BusRun [lower] FF Fluorescent [upper] Fluorescent [lower] BF BusRun [upper] Fluorescent [lower] BB BusRun [upper] BusRun [lower] fluobus: mounting options Ceiling Mounted Pendant Ceiling Mounted Level Glide Wall Mounted Please consult with Litelab for details. fluobus: accessories Top Lens H-ACC-TL-FR Coverplate/Fixture H-ACC-CV-P H-ACC-CV-MB H-ACC-CV-ST H-ACC-CV-NT White Black Silver Tone Brushed Aluminum Consult factory for layout. Bottom Lens H-ACC-BL-FR Bottom Louver Frosted H-ACC-LVR-MB Black fluobus: grid layout options Similar to Litelab’s BusRun Busway,...

251 Elm Street Buffalo, New York 14203 716.856.4300 800.238.4120 This document contains both conceptual renderings and products that are subject to change based on design, engineering, and manufacturing review and analysis.