EP COAT 100
2Pages

EP COAT 100 100% solids, pigmented performance epoxy coating for flooring applications Chemical resistance Permanent contact (3 days, 80ºC) Chemical Water Methoxypropyl acetate Isopropyl alcohol Skydrol Xylene Ammonia (3%) Acetone Diesel Hydrogen peroxide Sodium hydroxide (40 g/L) Bleach Sulphuric acid (10%) Sulphuric acid (30%) Sulphuric acid (50%) Acetic acid (10%) Pigmented, 2-component epoxy coating for concrete surface protection. Designed for general purpose uses in multilayer systems, from the primer coat to the topcoat layer. APPLICATION Multilayer protective coating for heavily used concrete floors, in all kinds of indoor areas. • Industrial flooring • Poorly ventilated areas. • Parking decks. • Warehouses. • Shops. This material can be used as a primer and as a component of all the steps in a multilayer system. Also suitable as a self-leveling flooring resin. The different available option depends on the application choices, fillers and the pigmentation options. Surface contact (24h, room temperature, 5=ok, 0=not recommended) TECHNICAL DATA Chemical Water Ethyl alcohol Engine oil Vinegar Hydrogen peroxide Sulphuric acid (10%) Sulphuric acid (30%) Sulphuric acid (50%) Isopropyl alcohol Xylene Ammonia (3%) Diesel Methoxipropyl acetate Acetic acid (10%) Bleach Sodium hydroxide (40 g/L) Acetone Skydrol INFORMATION ON THE PRODUCT BEFORE APPLICATION Chemical description Physical state Packaging Non-volatile content (%) Flash point Colour Density Epoxy resin Polyamine mixture Viscosity Approximate values Brookfield A/B mixing ratio Mixture properties A=100, B=25 by weight Density: 1,49 g/cm3 at 23ºC Viscosity: 1200 mPa.s at 23ºC Temperature (ºC) Pot life (100, min) 6 >70 25 40 35 25 Keep between 15ºC and 30ºC. Component A may crystallize if stored for protracted periods under certain conditions. If this occurs, it can be restored to its original condition by heating it to 70 - 80 °C and stirring it thoroughly. 12 months after manufacturing date. INFORMATION ON THE FINAL PRODUCT Final state Colour Hardness (shore) Fire behaviour UV resistance Use temperature Mechanical properties Rigid, glossy, homogeneous material Pigmented. Available colours are RAL 1003, 1014, 2010, 3002, 3009, 5015, 5017, 6002, 7001, 7004, 7011, 7035, 8024, 9005, 9003. Other colours under request. 80D (ISO 868) Bfl-s1 (EN 13501-1:2007) Undergoes slight yellowing under sunlight. No mechanical properties are affected. Up to 80ºC Maximum elongation: 2,5% Tensile strength: 17 MPa Tear: 29 N/mm SUPPORT REQUIREMENTS In order to achieve a good degree of penetration and bonding, support must be: 1. Flat and leveled (Product is self-leveling) 2. Compact and cohesive (pull off test must show a minimum resistance of 1,4 N/mm2). 3. Even and regular surface 4. Free from cracks and fissures. If any, they must be previously repaired. 5. Clean and dry, free of dust, loose particles, oils, organic residues or laitance. SUPPORT PREPARATION Concrete surfaces must be previously prepared by sandblasting or any other suitable means. Remove all dust and loose material before priming. The recommended temperature of the support is 15-25ºC, but not less than 10ºC. The temperature of the support must exceed the ‘’dew point’’ by 3ºC during application and drying. RECOMMENDED ENVIRONMENTAL CONDITIONS The recommended temperature of the support is 15-25ºC, but not less than 10ºC. The temperature of the support must exceed the ‘’dew point’’ by 3ºC during application and drying. MIXING Stir and homogenize thoroughly component A and B using a low-speed stirrer. The mixture turns to a homogeneous clear liquid. Mix the quartz filler afterwards if desired. Do not mix more material than the usable amount within the pot life window. APPLICATION Pure resin requires roller or rubber spreader or squeegee. Combinations with filler requires application by metal spreader. The pure resin is applied to roller or rubber rake. Combinations with aggregates may require the use of a metal trowel. In light colors it may be necessary to have more than 2 coats depending on the base color to obtain a good covering. Colours as RAL 1003, 1014, 2010, 3002 and 9003 will have a consumption of 600 g/m2, usually applied in several layers. KRYPTON CHEMICAL SL C/ Martí i Franquès, 12 - Pol. Ind. les Tàpies 43890 - l'Hospitalet de l'Infant - Spain Tel: +34 977 822 245 - Fax: +34 977 823 977 www.kryptonchemical.com – rayston@kryptonch

EP COAT 100 100% solids, pigmented performance epoxy coating for flooring applications CURING TIME Epoxy components are potentially sensitizing. Component B is corrosive. Always follow instruction provided in the Material Safety Data Sheet. As a general rule, suitable skin and eye protection must be worn. This product is intented to be used only for the uses and in the way here described. This product is to be used only by industrial or professional users. It is not suitable for DIY-type uses. REAPPLICATION Normally possible after 24 hours. Empty containers must be handled with the same...