Catalogs >
KOOLAIR S.A >
Long-throw nozzles – DF 89

Long-throw nozzles – DF 89
19Pages

Catalog excerpts

Selection and correction charts 5

Long-throw jet nozzle DF-89 Description The DF-89 long-throw jet nozzle and its flange are made of aluminium painted white RAL 9010 as standard finish. The connection part is manufactured of galvanised steel sheet. The DF89 nozzle has an extraordinarily good aesthetic design and can be painted by special order to fit any decorative need Application The DF-89 nozzles provide long throws with a low noise level, releasing a long air jet with exceptional precision to a length of over 30 metres. They can be used for spot cooling and are especially appropriate for large rooms requiring a...

Open the catalog to page 3

Dimensions Version A of the DF-89 jet nozzles can be mounted directly to the duct, plenum box or surface. Version C allows a flexible duct of standard dimensions to be coupled directly to each nozzle. In both cases, the nozzles are fixed by screws. In terms of the motor drive system, the motor may be placed inside or outside the unit, depending on the connection system and motor type (each case should be analysed separately). Please contact us for more information.

Open the catalog to page 4

Notes - This selection table is based on laboratory tests as per ISO 5219 (UNE 100.710) and ISO 5135 and 3741. - AT is equal to 0°C (isothermal air). - The behaviour of the air jet with different At is shown in the following charts. Symbols Q = Air flow VK = Effective velocity AK = Effective area APt = Total pressure drop LwA = Sound power X0,3 - X0,5 - Xi,0 = Throw for a terminal air velocity of 0.3, 0.5 and 1.0 m/s, respectively.

Open the catalog to page 5

DF-89 DF-89 model Selection charts DF-89-1.- Maximum vertical penetration.

Open the catalog to page 6

DF-89 model DF-89-2.- Velocity of the air jet for the throw.

Open the catalog to page 7

DF-89 model DF-89-3.1.- Vertical deviation of the air jet (non-isothermal jets).

Open the catalog to page 8

DF-89 model DF-89-3. 2.- Vertical deviation of the air jet (non-isothermal jets).

Open the catalog to page 9

DF-89 model DF-89-3. 3.- Vertical deviation of the air jet (non-isothermal jets).

Open the catalog to page 10

DF-89 model DF-89-3. 3.- Vertical deviation of the air jet (non-isothermal jets).

Open the catalog to page 11

DF-89 model DF-89-3. 4.- Vertical deviation of the air jet (non-isothermal jets).

Open the catalog to page 12

DF-89 model DF-89-4.- Ratio between air flow velocities. DF-89-5.- Ratio between temperature differences.

Open the catalog to page 13

DF-89 DF-89 model DF-89-6.- Induction rate. DF-89-7.- Pressure drop and sound power level.

Open the catalog to page 14

DF-89 Selection in a sample project Initial data Two DF-89 nozzles are located, one in front of the other at a distance of 24 m, with the following starting data based on the sketch attached in the Symbols section on page 16. - L = 12 m - H = 4 m (height from floor) - Qnozzle = 400 l/s - Supply temperature = 15° C - Room temperature = 25° C - AT0 = -10° C - Hh = 2 m (height of occupied area) The diffuser should be selected to obtain the following: - Maximum velocity in the occupied area: 0,2 m/s. - The vertical temperature gradient must not exceed 3 °C. - The sound power level of the...

Open the catalog to page 15

DF-89 Selection - DF-89 quick selection table (page 4) Based on the sound power limit, size 16 is preselected. - DF-89-7 chart (page 13) Using size 16 for 400 l/s, the following values are obtained: - APt= 54 Pa (pressure drop) - LwA= 34 dB(A) (sound power level) - DF-89-2 chart (page 6) For a supply angle of aX= +15° C, The throw will be I=L/cos 15°=12/0,966=12,42 m According to the chart, the velocity for this throw is VX=1,2 m/s - DF-89-3.4 chart (page 11) The impact point under isothermal conditions would be H+HC=H+(L x tan 15°)=4+(12x0,268)=7,2 m The chart indicates that for AT0 = -10°...

Open the catalog to page 16

DF-89 Symbols Common symbols used in all tables and charts in the catalogue. Distance between the equipment to the impact point of the jets (with another jet or wall) under isothermal conditions. Supply angle. Horizontal distance from the equipment to the impact point of the jets (with another jet or wall). Throw of the air jet. Deviation of the air jet caused by a temperature difference between the supply and ambient air. Installation height of the equipment. Height of occupied area. Height from the impact point of the jets (with another jet or wall) under isothermal conditions with...

Open the catalog to page 17

THIS CATALOGUE IS INTELLECTUAL PROPERTY. Reproduction, either partial or total, by any means, including electronic, is prohibited without prior written authorisation from KOOLAIR, S.A. . CEN-DF-89-0815-00

Open the catalog to page 18

KOOLAIR, S.A. Calle Urano, 26 Poligono industrial nº 2 – La Fuensanta 28936 Móstoles - Madrid - (España) Tel: +34 91 645 00 33 Fax: +34 91 645 69 62 e-mail: info@koolair.com

Open the catalog to page 19

Long-throw nozzles – DF 89 19Pages

Catalog excerpts

All KOOLAIR S.A catalogs and technical brochures

Long-throw nozzles – DF 89
19Pages