Eveness/ Tolerances Power supply via busbar on the ground Design with: – power supply via busbar – power supply via contact wire – power supply via trailing cable Top edge finished floor Tolerances for the evenness of the carriageway must be strictly complied with in accordance with DIN (= German Industrial Standard) No. 18202, chart 3, line 3. Electrical installation Technical data Dimensions All space requirements are minimum finished dimensions. Tolerances for space requirements + 3 . 0 Dimensions in cm. To be performed by the customer Description Direction of shifting movement Standard passenger cars: Limousine, station wagon, SUV, van, according to specifications in the table and maximal surface load. Conductor rail (dowelled on top edge of finished floor) Power supply via trailing cable on the ceiling Headroom according to local regulations Headroom according to local regulations Power supply via contact wire on the ceiling Guide rail length weight wheel load Conductor rail Contact wire Power pole Cable roll conveyor Trailing cable Power pole A safety clearance of 30 cm must be maintained between the front or rear bumpers of vehicles on ParkBoards and any fixed parts of the surroundings or other vehicles in accordance with DIN EN 14010. At a max. vehicle length of 500 cm, this means a length dimension of 560 cm between the columns. The length dimension of 560 cm can only then be shortened if the max. vehicle or parking place length is reduced or light barriers are used. The operating console must be mounted in such a way that the operator can see the entire system during operation and the motion sequences can be observed and monitored. 1 2 3 Standard type Special system: maximum load for extra charge. Conduit with taut wire to control box (is entered in the layout plan by KLAUS Multiparking). To follow the minimum finished dimensions, make sure to consider the tolerances according to VOB, part C (DIN 18330 and 18331) and the DIN 18202. ParkBoard PQ | Code number 586.23.230-003 | Version 10.2017 Recess/ Rail system PRODUCT DATA

ParkBoard PQ I Code number 586.23.230-003 I Version 10.2017 Page 1 Dimensions Car data Dimensions Page 2 Dimensions Recess/ Rail system Page 5 To be performed by the customer Description A Vehicle C D E Please note the following on parking space DH 560 500 30 97 130 Parking space and ParkBoard conform to German regulations and DIN EN 14010 acc. to local 530 500 15 82 115 Where the unit is equipped with ligth barriers, parking space and pallet also conform <530 <500 15 <82 <115 Light barrier is essential. Parking space does not conform to German regulations....

Dimensions Recess/ Rail system ParkBoard PQ | Code number 586.23.230-003 | Version 10.2017 Evenness and Tolerances (abstract from DIN 18 202, table 3) The distance between the lower flange of the ParkBoards and the garage ground must therefore not exceed 2 cm. To adhere to the safety regulations and DIN EN 14 010 recommendations and to get the necessary even ground, the tolerances of evenness to DIN 18202, table 3, line 3, must not be exceeded. Therefore exact levelling of the ground by the client is essential. Column Eveness/ Tolerances Technical data Finished grounds, e.g. floor pavement serving...

Dimensions Recess/ Rail system Eveness/ Tolerances Electrical installation Technical data To be performed by the customer Description ParkBoard PQ | Code number 586.23.230-003 | Version 10.2017 Electrical installation Electrical supply / Control system The customer must provide a supply line 5 x 2.5 mm2 (3 PH+N+PE) to the main cabinet. The location of the main cabinet and control panel are specified in the layout plans provided by Klaus Multiparking. Provide conduits EN 25 (M25) with taut wire to the contact line at the floor (only for PQ with busbar on ground). Page 4 of 5 Drive / Safety Safety...

Dimensions Recess/ Rail system Eveness/ Tolerances Electrical installation Technical data To be performed by the customer Description ParkBoard PQ | Code number 586.23.230-003 | Version 10.2017 To be performed by the customer Numbering of parking spaces Consecutive numbering of stationary parking spaces and crosswise shifting ParkBoards. Building services Any required lighting, ventilation, fire extinguishing and fire alarm systems as well as clarification and compliance with the relevant regulatory requirements. Floor / Rails Flooring structure in accordance with our instructions, please see page...