KILZ® ORIGINAL INTERIOR OIL-BASED PRIMER
4Pages

TECHNICAL DATA SHEET AS OF 6/1/2011 COMPLIES OR IS CERTIFIED WITH: ' Applies lo both formulas. KILZ® ORIGINAL INTERIOR OIL-BASED PRIMER KILZ® Original primer blocks out most stains Including water, smoke, tannin, Ink, pencil, felt marker and grease, and seals pet and smoke odors. Use on Interior surfaces. Not recommended Use on properly prepared Interior surfaces, such as Properly Prepared Glossy Surfacest FILL/MAX TINT "Tinting is not recommended for stainblocking Sheen levels depend on porosity and various surface Vehicle: Alkyd Resin Vehicle: Alkyd Resin The addition of colorants may add VOCs. COVERAGE RATE gallon, depending on the surface texture, porosity and application method. Does not Include the loss of material from spraying, RECOMMENDED FILM THICKNESS •No. 1003 (350 VOC)-Wet: 4.0 mils; Dry: 2.1 mils PREMIUM APPLICATION TOOLS Airless Spray: Rough / Porous Surfaces: 1/2" - 3/4" nap Brush: Nylon / Polyester Blend or Premium Natural Bristle SURFACE PREPARATION! •The surface must be clean, free of dust, grease, wax, peeling paint, mold, mildew and wallpaper paste. If washing Is necessary, use a non-soapy detergent or a TSP substitute. Rinse well and • Peeling or Checked Paint: Scrape off loose paint and sand to a smooth surface. Sanding or removal of paint containing lead Is hazardous.! • Glossy Surfaces: For maximum adhesion, scuff sand the surface thoroughly before prlmlng.f • Mold or Mildew Covered Surfaces: Wash the area with a mildew remover, rinse with water and allow to dry before priming. Note: KILZ® PREMIUM and KILZ 2® primers are recom- mended for mildew-prone surfaces. • Masonry, Brick, Stucco and Plaster: KILZ ORIGINAL primer may be used on clean, dry, aged masonry surfaces that have cured (dried) at least 90 days. If masonry has been cured less than 90 days, use KILZ® PREMIUM, KILZ 2® or KILZ ODORLESS® primers. • Fire Restoration: It Is critical to clean smoke damaged surfaces thoroughly before • Apply as supplied using a brush, roller or • Stir thoroughly before and occasionally • Prime the entire surface to ensure a uniform • Stainblocking: After priming, test for stain bleed-through by applying the topcoat to a small section. If the stain bleeds through the topcoat, apply a second coat of primer and test again before topcoatlng the entire area. If bleeding continues, a longer dry time Is needed before topcoatlng. • Tinting: Not recommended for stainblocking applications. KILZ ORIGINAL primer may be tinted with up to 2 ounces of universal colorant per gallon for non-stalnblocklng projects. Tinting to a lighter shade than the Application at lower temperatures, high humidity or poor ventilation will affect dry time. This information is provided "as is" and no representations or warranties, either express or implied, of merchantability, fitness for a particular purpose or of any other nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a technical service representative, call 1-866-PRIMER-1.

KILZ® ORIGINAL INTERIOR OIL-BASED PRIMER • Clean equipment and paint spatters with mineral spirits. • If spilled, contain material and remove with an inert absorbent. Dispose of contaminated absorbent, container and unused product in accordance with al current federal, state and local regulations. • Do not dispose of this product down a drain, • Please consider donating any unused product. • For recycling or disposal Information, contact your local household refuse collection service, LIMITED WARRANTY If this product is found to be defective upon inspection by its representative, Masterchem...

TECHNICAL DATA SHEET AS OF 6/1/2011 COMPLIES OR IS CERTIFIED WITH: KILZ ORIGINAL INTERIOR AEROSOL PRIMER KILZ® Original Interior aerosol primer, sealer and stalnblocker blocks out most stains caused by water, smoke, tannin, Ink, pencil, felt marker and grease, and seals pet and smoke odors. Use on properly prepared Interior surfaces, such as: • Painted Metal • Properly Prepared Glossy Surfacest Sheen levels depend on porosity and various surface Vehicle: Modified Alkyd COVERAGE RATE container, depending on the surface texture, porosity and application method. Does not Include the loss of...

TECHNICAL DATA SHEET KILZ® ORIGINAL INTERIOR AEROSOL PRIMER • Clear spray valve Immediately after use by turning can upside down and spraying until only clear gas Is released, • If spray nozzle becomes clogged, remove and clean. Do not stick pins or wire Into can opening. • Replace nozzle with valve opening pointed away from you. • Clean fresh overspray with mineral spirits or paint thinner. Remove dried paint with paint remover, but test small area first to ensure paint remover does • Please consider donating any unused product. • For recycling or disposal Information, contact your local...