TECHNICAL DATA SHEET KILZ® KWIK-START® KILZ® KWIK-START® primer is a fast drying, latex, primer sealer formulated to minimize problems caused by color changes, minor stains, surface textures and porosity differences. When brushed, rolled or sprayed it can be topcoated after one hour with latex or oil-base paint. Not recommended for floors. AS OF 8/1/2013 COMPLIES OR IS CERTIFIED WITH: SCAQMD OTC LADCO FILL / MAX TINT No. 59001 / 59000 White Gallon – 128oz / 2oz 5 Gallon – 640oz / 10oz FINISH 85° = < 10.0 Sheen levels depend on porosity and various surface irregularities. COMPOSITION Vehicle: PVA/Acrylic Weight Solids: 49% (+/-) 2% Volume Solids: 39% (+/-) 2% Weight / Gallon (lbs): 11.5 (+/-) 0.2 Viscosity: 101 - 109 KU VOC: 50 g/L The addition of colorants may add VOCs. FLASHPOINT N/A COVERAGE RATE Coverage: 300 - 400 sq. ft. (28 - 37 m2) per gallon, depending on the surface texture, porosity and application method. Does not include the loss of material from spraying. RECOMMENDED FILM THICKNESS At 300 sq. ft. per gallon: • Wet: 6.4 mils; Dry: 2.5 mils At 400 sq. ft. per gallon: • Wet: 4.0 mils; Dry: 1.6 mils PREMIUM APPLICATION TOOLS Airless Spray: Tip: .015” - .021” Filter: 60 mesh PSI: Fluid pressure of 1,500 - 2,200 Roller: Smooth Surfaces: 3/8” - 1/2” nap Porous Surfaces: 1/2” - 3/4” nap Brush: Nylon / Polyester Blend WHERE TO USE Use KILZ KWIK-START primer on interior surfaces, including: • Drywall • Cured Plaster • Woodwork • Masonry • Brick SURFACE PREPARATION† • All surfaces must be clean, free of dust, chalk, oil, grease, wax polish, mold and mildew, loose peeling paint, rust and all other foreign substances. • If washing is necessary, use a non-soapy detergent or TSP substitute. Rinse well and allow to dry. • Fill all gaps with paintable sealant and allow to completely dry prior to coating. • Peeling or Checked Paint: Scrape off loose paint and sand to a smooth surface. Sanding or removal of paint containing lead is hazardous. • Glossy Surfaces: KILZ MAX™, KILZ® PREMIUM and KILZ 2® primers are recommended for use over properly prepared glossy surfaces. • Mold & Mildew Covered Surfaces: Wash the area with a milde remover, rinse with water and allow to dry before priming. Note: KILZ® PREMIUM and KILZ 2® primers are recommended for mildew prone surfaces. • Masonry, Brick, Stucco and Plaster: KILZ® KWIK START® primer may be used on clean, dry, aged interior masonry surfaces that have cured (dried) at least 90 days. If masonry has cured less than 90 days, use KILZ® PREMIUM, KILZ 2®, or KILZ ODORLESS® primers. • Stainblocking: KILZ® KWIK-START® primer is formulated to block minor stains before topcoating; for heavy stains use KILZ MAX, KILZ® PREMIUM, KILZ® ORIGINAL, KILZ COMPLETE® or KILZ ODORLESS® primers. • Tinting: May be tinted with up to 2 ounces of universal colorant per gallon. DRY TIME at 77°F (25°C), 50% RH: • To Touch: 30 Minutes • To Recoat: 1 Hour Longer dry time required in cooler temperatures and in higher humidity. APPLICATION • Eye protection is recommended. • For spray applications, a small amount of water (no more than ½ pint per gallon) may be added. • Only apply if surface, air and product temperatures are between 50º – 90ºF (10º – 32ºC). • Stir thoroughly before and occasionally during use. • Apply using a brush, roller or sprayer. • Prime the entire surface to ensure a uniform appearance of the topcoat. This information is provided “as is” and no representations or warranties, either express or implied, of merchantability, fitness for a particular purpose or of any other nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a technical service representative, call 1-866-PRIMER-1. ©2013 Masterchem Industries, 3135 Old Hwy M, Imperial, MO 63052-2834 1-866-PRIMER-1 • www.kilz.com

TECHNICAL DATA SHEET KILZ® KWIK-START® CLEAN UP & DISPOSAL • Clean equipment and paint spatters with warm, soapy water. • Do not dispose of this product down a drain. • If spilled, contain material and remove with an inert absorbent. Dispose of contaminated absorbent, container and unused product in accordance with all current federal, state and local regulations. • Please consider donating any unused product. • For recycling or disposal information, contact your local household refuse collection service. CAUTIONS / LIMITATIONS • IMPORTANT! DO NOT OPEN CAN WITHOUT READING INSTRUCTIONS • INTERIOR...