TECHNICAL DATA SHEET AS OF 8/1/2013 COMPLIES OR IS CERTIFIED WITH: SCAQMD OTC LADCO KILZ® KLEAR™ High Performance Sealer is a fast dry multi-surface clear primer developed to seal porous surfaces inside and outside your home. Particularly effective for ‘same color painting’, KILZ KLEAR will bond and seal porous and chalky surfaces with little change to current color. KILZ KLEAR is a tough, flexible and breathable film to offer years of service. KILZ KLEAR may also be used to seal highly porous surfaces with a transparent flat finish. Suitable for sealing torn drywall facing paper, dried wallcovering adhesive, ‘hot’ joint compounds, concrete and stucco. Not recommended for floors. WHERE TO USE Use KILZ KLEAR primer on interior and exterior surfaces, including: • Masonry • Drywall • Galvanized • Brick • Plaster • Aluminum • Wood • Architectural Plastics FILL / MAX TINT No. L220101 / L220105 Clear Gallon – 128oz / 2oz 5 Gallon – 640oz / 10oz FINISH 85° = < 10 Sheen levels depend on porosity and various surface irregularities. COMPOSITION Vehicle: Styrene Acrylic Weight Solids: 20% (+/-) 2% Volume Solids: 17% (+/-) 2% Weight / Gallon (lbs): 8.5 (+/-) 0.2 Viscosity: 60 - 65 KU VOC: < 100 g/L The addition of colorants may add VOCs. FLASHPOINT N/A COVERAGE RATE Coverage: 300 - 400 sq. ft. (28 - 37 m2) per gallon, depending on the surface texture, porosity and application method. Does not include the loss of material from spraying. RECOMMENDED FILM THICKNESS At 300 sq. ft. per gallon: • Wet: 6.4 mils; Dry: 1.1 mils At 400 sq. ft. per gallon: • Wet: 4.8 mils; Dry: 0.8 mils PREMIUM APPLICATION TOOLS Airless Spray: Tip: .015” - .017” Filter: 60 mesh PSI: Fluid pressure of 1,000 - 1,800 Roller: Smooth Surfaces: 3/8” - 1/2” nap Porous Surfaces: 1/2” - 3/4” nap Brush: Nylon / Polyester Blend SURFACE PREPARATION† • All surfaces must be clean, free of dust, chalk, oil, grease, wax polish, mold and mildew, loose peeling paint, rust and all other foreign substances. • If washing is necessary, use a non-soapy detergent or TSP substitute. Rinse well and allow to dry. • Peeling or Checked Paint: Scrape off loose paint and sand to a smooth surface. Sanding or removal of paint containing lead is hazardous. • Glossy Surfaces: Use over properly prepared glossy surfaces, scuff-sand to de-gloss and wipe clean before application. • Mold & Mildew Covered Surfaces: Wash the area with a mildew remover, rinse with water and allow to dry before priming. To reduce waste, consult with your retailer or an online paint calculator to determine the correct amount of paint to purchase. DRY TIME at 77°F (25°C), 50% RH: • To Touch: 30 Minutes • To Recoat: 1 Hour Longer dry time required in cooler temperatures and in higher humidity. APPLICATION • Stir thoroughly before and occasionally during use. • Only apply if surface, air and product temperatures are between 50º – 90ºF (10º – 32ºC) • Do not thin or apply at a greater spread rate or build up a visual glaze on the surface. Product is formulated for use at package consistency only. • Apply using a brush, roller or sprayer • Prime the entire surface to ensure a uniform appearance of the topcoat. • If rain or threatening weather is expected within 8 hours, delay applications until dry conditions exist. • Never apply product to wet or water saturated substrates or when the relative humidity is above 90%. • Not for use below grade or under water. • Do not flood coat • Must be top coated within 7 days of application or the surface may need to be re-cleaned. ® This information is provided “as is” and no representations or warranties, either express or implied, of merchantability, fitness for a particular purpose or of any other nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a technical service representative, call 1-866-PRIMER-1. ©2013 Masterchem Industries, 3135 Old Hwy M, Imperial, MO 63052-2834 1-866-PRIMER-1 • www.kilz.com

TECHNICAL DATA SHEET CLEAN UP & DISPOSAL • Clean equipment and paint spatters with warm, soapy water. • Do not dispose of this product down a drain. • Please consider donating any unused product. • If spilled, contain material and remove with an inert absorbent. Dispose of contaminated absorbent, container and unused product in accordance with all current federal, state and local regulations. • For recycling or disposal information, contact your local household refuse collection service. CAUTIONS / LIMITATIONS • IMPORTANT! DO NOT OPEN CAN WITHOUT READING INSTRUCTIONS • DO NOT USE ON FLOORS •...