LAYING RANGE / Waterproofing Aquastop Green Anti-cracking waterproof membrane with high adhesion for balconies, terraces and horizontal surfaces before the laying of ceramic tiles, natural stone and hardwood floors; it creates a waterproof surface even when overlaid on cracked supports, supports that have not been perfectly cured or supports that might contain vapour pressure due to residual substrate moisture content. CONTACT POWER ANTI FRACTURE VAPOUR DIFFUSION Aquastop Green revolutionises the world of underlying waterproofing, rewriting performance standards to allow applications that are impossible for mineral products. KERAKOLL PATENT PRODUCT STRENGTHS Aquastop Green is a highly innovative Kerakoll creation. The membrane is a high-technology, multi-layer composite polymer system comprising: • It waterproofs any surface, old or new, damp or dry, cracked or subject to dimensional variations • PA - hydrophobic PA fibres with high tensile strength to guarantee a superior and more evenly distributed available contact surface • HDPE - waterproof and variable geometry HDPE structure to guarantee physical separation between the substrate and the flooring • It compensates for hygrometric shrinkage and thermal deformation stress • It reduces on-site working times: waterproofing and laying of the coating without waiting, withstands foot traffic immediately • Solves the problem of respecting substrate joints in staggered or diagonal laying (cuts in doorways) • Non-woven fabric - highly breathable sheet to guarantee passage of the vapour from uncured screeds or screeds with high residual humidity and to guarantee high levels of adhesion to the substrates Use For internal and external use to waterproof, separate and compensate for vapour pressure prior to laying of ceramic tile, natural stone and hardwood floor coverings for domestic, commercial, industrial applications (such as industrial kitchens, food industries, warehouses) and for street furniture (check that the size and thickness of the materials to be laid is suitable). Balconies, terraces, flat roofs and surfaces of any size. Substrates: - creeds, including any that are cracked and not completely cured or with possible vapour pressure caused by residual humidity, heats radiant slabs - existing ceramic, marble floor tiles, natural stone floorings anchored to the substrate - cured concrete - fibre-cement and plaster-board panels anchored to the substrate. Do not use On anhydrite-based substrates without the use of Primer A Eco professional, concentrated, water-based surface insulation, on bituminous sheeting, on exposed surfaces, on inverted roofs made with insulation panels or low-density screeds. * ÉMISSION DANS L’AIR INTÉRIEUR Information sur le niveau d’émission de substances volatiles dans l’air intérieur, présentant un risque de toxicité par inhalation, sur une échelle de classe allant de A+ (très faibles émissions) à C (fortes émissions). Aquastop Green Code: IM1

INSTRUCTIONS FOR USE STORAGE Protect the rolls from direct sunlight, heat sources and rain, both during storage in the warehouse and on site. When laying the sheets, protect them from sunshine until shortly before application. PREPARATION OF SUBSTRATE 1 Check the mechanical performance and surface consistency of the laying substrate. 2 Check that old flooring is properly anchored and clean. 3 Check that the movements of the joints and cracks of the substrate are ≤ 1 mm, respect the structural joints. 4 The residual humidity level in the screed, when measured with a carbon hygrometer, must be...

INSTRUCTIONS FOR USE 5 Regulate the thickness by the tilt of the spreader, using the toothed part. Apply the gel adhesive to a surface area that will allow laying of the sheets within the open time indicated (check the state of the adhesive frequently). Avoid any build-up of gel adhesive that might compromise the flatness of the sheets. 6 Position the sheets or unroll them onto the fresh gel adhesive, taking care they are flat and avoiding the formation of creases or bubbles. 7 Create joints approximately 5 mm in width between the sheets and the perimeter walls, stringcourses, etc., and between...

INSTRUCTIONS FOR USE PERIMETER WATERPROOFING 1 Lay the sealant along the perimeter in the vicinity of the wall-floor corner joints: lay the sealant both on the wall and on the membrane in strips approximately 8-10 cm in width. 2 Position Aquastop 120 and smooth carefully. 3 Remove any excess Aquastop Fix that may have seeped out from under the tape, and take care to ensure the edges of the tape are fixed to the membrane. When waterproofing the wall-floor joint, lay about 10 cm Aquastop 120 over the special pieces. • Clean the surface of the sheets carefully; check that the plaster/render in the...

INSTRUCTIONS FOR USE JOINING THE WATERPROOFING LAYER TO AQUAFORM DRAINS 1 Lay Aquastop Fix on the black TNT connection surfaces of the AquaForm drains and on the adjacent surfaces to be connected . 2 Position the special pieces of Aquastop 120 cut to measure. Press firmly and smooth over to ensure the tape seals perfectly, being careful not to wrinkle it. Use several pieces of tape until the drain has been completely sealed (black TNT totally covered). • as for the connection with Aquaform SD – VD, see the application procedures provided on the relevant technical data sheet. WATERPROOFING: SPECIAL...

INSTRUCTIONS FOR USE LAYING THE FLOOR 1 Apply a first layer of Biogel® gel adhesive to fill in the circular cavities; use the smooth part of the spreader. 2 Adjust the thickness of the gel adhesive using a toothed spreader of a type suited to the size of the tile. Lay the flooring with open joints, with gaps of a minimum width from 2 - 3 mm according to the size of the tile. 3 Check that the entire back of the tile is impregnated, to guarantee the suitability of the adhesive system. 4 Grout the gaps using Fugabella® Color. 5 Seal the elastic joints using Silicone Color or Neutro Color. ® * If...