video corpo

M SERIES
24Pages

{{requestButtons}}

Catalog excerpts

M SERIES - 1

I KEISEiIRL STRENGTH | CARDIO | FUNCTIONAL BECAUSE... 'GOOD ENOUGH' ISN'T." M SERIESvueMM M3i INDOOR GROUP CYCLE INSTALLATION AND OPERATION MANUAL

Open the catalog to page 1
M SERIES - 2

03 - IMPORTANT SAFETY INSTRUCTIONS 04 ~ INTRODUCTION 04 ~ WEIGHT AND FOOTPRINT 04 - ASSEMBLY 04_TOOLS REQUIRED FOR ASSEMBLY 05_PARTS LIST 06_PRODUCT OVERVIEW 07_MOUNTING THE CYCLE TO THE BASE 07_INSTALLING THE FLYWHEEL AND HUBCAP 08_INSTALLING THE FLYWHEEL GUARD 09_INSTALLING THE PEDALS 10_INSTALLING THE COMPUTER 10_ASSEMBLING THE HANDLEBAR 12_ASSEMBLING THE DEVICE HOLDER 12_APPLY THE HOLE COVER DECALS 12_FINAL INSTALLATION AND CHECKING FOR PROPER OPERATION 13_SETTING TRIP UNITS TO MILES OR KILOMETERS (KM) AND BIKE ID NUMBER 14 ~ M3i SERIES COMPUTER 16 ~ SET UP AND OPERATION 16_EMERGENCY...

Open the catalog to page 2
M SERIES - 3

M3i INDOOR GROUP CYCLE IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Only use replacement parts recommended by Keiser Corporation. 6. Replace defective components immediately and/or keep the equipment out of use until repaired. 7. Routinely check and pay special attention to components most susceptible to wear. 8. Maximum weight of the rider shall not exceed 300 lbs (136 kg). 9. The cycle is NOT designed with a freewheel, but a fixed gear system. When the flywheel is in motion, the pedals will also...

Open the catalog to page 3
M SERIES - 4

M3i INDOOR GROUP CYCLE 04 INTRODUCTION Thank you for purchasing Keiser's premier M3i indoor cycle. Your new resistance system is a revolutionary way to exercise providing a smoother, quieter, and more predictable workout. WEIGHT AND FOOTPRINT

Open the catalog to page 4
M SERIES - 5

* Hub Cover Decal will be shipped with, and are to be installed on, the M3i sold within the European Union only.

Open the catalog to page 5
M SERIES - 6

M3i INDOOR GROUP CYCLE PRODUCT OVERVIEW Seat Forward/Backward Seat Adjustment Handle 3 Up/Down Seat Adjustment Knob [4 Flywheel Guard 3 Belt Cover 3 Flywheel Leveling Foot Base 3 Stretch Pads Device Holder Computer System with Bluetooth® smart Resistance Lever/Emergency Brake Neutral Position Handlebar Forward/Backward Handlebar Adjustment Handle Up/Down Handlebar Adjustment Knob Water Bottle Holder Keiser® M Series Bike Pedals [1^ Transport Wheels

Open the catalog to page 6
M SERIES - 7

M3i INDOOR GROUP CYCLE MOUNTING THE CYCLE TO THE BASE NOTE: Due to the weight of the cycle, it is recommended that two people perform this part of the assembly. 1. Align the holes of the cycle with the studs of the base, refer to Figure 1. The front of the cycle should face the wheels of the base. 2. Place the cycle onto the base. 3. Insert a washer (supplied) on each of the four studs. 4. Install an acorn nut (supplied) on each stud and then hand tighten the acorn nuts. 5. Torque the acorn nuts to 45 Nm (35 ft-lbs) using a 16 mm or 5/8” crowfoot attached to a torque wrench. Figure 1. Cycle...

Open the catalog to page 7
M SERIES - 8

M3i INDOOR GROUP CYCLE 3. Align the holes of the flywheel with the holes of the hub. NOTE: The flywheel should be flush against the hub. 4. Install the hubcap: a) Align the holes of the hubcap with the holes of the flywheel, refer to Figure 4. b) Hold the flywheel in position. c) Use the five, M6x1x18 SS socket head cap screws (supplied) and a 5 mm Allen wrench and tighten the screws. d) Be sure the flywheel is flush against the face of the hub. Spin the flywheel to make sure the it runs true and straight (no wobbling). Figure 4. Flywheel and Hubcap Installation INSTALLING THE FLYWHEEL...

Open the catalog to page 8
M SERIES - 9

M3i INDOOR GROUP CYCLE 4. Attach the brackets on the end of the flywheel guard, refer to Figure 8. Use the M6 x 1 x 45 hex head screw and nut (supplied). Hand tighten the screw and nut. 5. Tighten the brackets to the base frame with the two Allen screws and washers removed in step 1. Do not fully tighten the bolts. 6. Check to ensure that there is enough clearance between the flywheel and the flywheel guard. 7. Using 2, 10 mm wrenches and a 5 mm Allen wrench, tighten the bolt and screws to secure the flywheel guard centered with the flywheel. Figure 8. Align, Attach, and Tighten Flywheel...

Open the catalog to page 9
M SERIES - 10

M3i INDOOR GROUP CYCLE INSTALLING THE COMPUTER 1. Use a #2 Phillips screwdriver and remove the computer mounting screw from the handlebar tube, refer to Figure 11. 2. Coil the computer cable into the computer mount Figure 11. Remove Mounting Screw From Handlebar Tube cavity, refer to Figure 12. 3. Slide the computer up into the two locking ears. 4. Insert and secure the computer with the screw previously removed using a #2 Phillips screwdriver. Figure 12. Attach the Computer to the Handlebar Tube ASSEMBLING THE HANDLEBAR 1. Remove screws from both sides of the sweat guard, refer to Figure...

Open the catalog to page 10
M SERIES - 11

M3i INDOOR GROUP CYCLE 5. Attach the handlebar slide to the handlebar tube with the four 8 mm screws previously removed. Use a 6 mm Allen wrench to tighten screws. There should be Figure 15. Remove the 8 mm Screws From the Handlebar 6. Install the handlebar on the handlebar slide: 11 no gap between the handlebar slide and the handlebar tube, refer to Figure 16. Figure 16. Attach the Bottom Slide to the Handlebar Tube a) Disassemble the L-handle assembly. Use a 5 mm Allen wrench and remove the screw and washer to remove the handle stud. c) Place the L-handle onto the handle stud. The...

Open the catalog to page 11
M SERIES - 12

M3i INDOOR GROUP CYCLE ASSEMBLING THE DEVICE HOLDER To install the device holder, apply force in the direction shown in Figure 19. The device holder will fit to the handlebars as shown in Figure 20. Figure 20. The assembled handlebar and device holder Figure 19. Assemble the device holder to the handlebar APPLY THE HOLE COVER DECALS Install the hub cover decals as shown in Figure 21. The decals should completely cover each of the 5 holes on the flywheel hubcap. Figure 21. Hole Cover Decal Placement FINAL INSTALLATION AND CHECKING FOR PROPER OPERATION NOTE: Perform the operations below...

Open the catalog to page 12
M SERIES - 13

M3i INDOOR GROUP CYCLE SETTING TRIP UNITS TO MILES OR KILOMETERS (KM) AND BIKE ID NUMBER (Unless otherwise specified or requested at the time of purchase, the M3i trip distance is set to miles.) NOTE: STEPS 1 THROUGH 7 MUST BE COMPLETED WITHIN 1 MINUTE 2 Begin with the bike off, push shift lever Pedal 1 full revolution. The bike all the way down id (bid) in the screen above is 0, yours may be different. Also, notice the 1 in the “TIME ROW”. Set shift lever to gear 21 for Miles, or set shift lever to gear 19 for Kilometers. TIME ROW Pedal 1 full revolution. Notice the 2 in the “TIME ROW”....

Open the catalog to page 13

All Keiser catalogs and technical brochures

  1. POWER RACK

    2 Pages

  2. M5i STRIDER

    2 Pages

  3. A300 SQUAT

    2 Pages

  4. m3i

    15 Pages

  5. AIR300 SQUAT

    2 Pages

  6. SIX PACK

    2 Pages