ACRYLIC STAINS ACRYLIC-BASED CHEMICAL STAIN FOR CONCRETE GENERAL CHARACTERISTICS KDF ACRYLIC STAIN is a penetrating, acrylic-based stain used to color old or new concrete. KDF ACRYLIC STAIN provides a translucent, permanent color with a shaded marbled effect, similar to the aged appearance of natural stone. KDF ACRYLIC STAIN's rich variegated finish will not peel, crack, chip, or fade from UV light. KDF ACRYLIC STAIN can also be used over concrete overlays and over stamped concrete floorings.     Applied on integrally-colored concrete or over color-hardened concrete. Provides variegated appearances and long-lasting durability that will not peel or chip. Can be applied horizontally. Can be easily cleaned and maintained. Available in 9 colors with two shades each. Bulk Density: Adhesive strength: Temperature for the application and drying of the material: Concrete quality: Moisture content: Acrylic resin SUBSTRATE REQUIREMENTS Basis: Appearance: TECHNICAL DATA Ideal for stamped concrete or microtopping POLART floor or over KNOCK DOWN floorings, residential or commercial applications, hotels, entryways, restaurant floors, showrooms, patios, pool decks, basements or garage floors, large commercial projects, driveways, sidewalks. Caution must be taken so that temperature of the substrate as well as ambient air remains ο above 12 C during application and curing of the materials while relative environm

does not exceed 75%. PREPARATION For best results, concrete must cure for a minimum of 30 days. Concrete should be clean and free of curing compounds, sealers, paints, coating and other bond breakers. Old paint or coatings must be removed mechanically. Oil, grease, and dirt must be removed, rinsed or pressure washed thoroughly, and the surface allowed to dry completely. Concrete must be etched, because a profiled porous surface is required. So it is strongly recommended the usage of special chemical cleaning with the parallel wash out with water under pressure. When the surface is completely...

• Stained concrete must be protected from any source of water or excessive moisture. Material will not freeze in storage but should be allowed to rise to 10 °C or more before use. • Excessive build-up of STAIN SEALER or puddling of the product during application can lead to bubbling and discoloration. • Do not mix or apply unless surface, air and material temperatures are over 12°C during the next 24 hours or if rain is expected within 12 hours after application. • Do not apply to floors if there is moisture in the subfloor drive or hydrostatic pressure. Prior precautions measurements of humidity...

GENERAL CHARACTERISTICS POLFLOOR-PU 807 is polyurethane-based, anti-dust, transparent or colored, two-component resin.  Creates colored, easy-to-clean indoor or outdoor floorings. Ideal for old and new surfaces, for light and middle circulation such as industrial, troweled floorings, mosaics, cement surfaces, workshops, and storehouses. Suitable even for metallic surfaces and for painting swimming pools. Provides permanent protection from U.V. radiation. Eliminates dust and decay from old & new floorings, reinforcing their durability. Offers high mechanical resistance and chemical protection...

Applied only on dry surfaces. Protected from arising humidity and free of materials that might prevent bonding e.g. dust, loose particles, grease etc. The success in the application depends on the right preparation of the underlay and use of the material.  Grinding of the surface with a mosaic machine, or sandblast and rotor machine in case of vertical surfaces. Good, dry cleaning of the surface from dust and residues with vacuum cleaner and squeegees. Caution must be taken so that temperature of the substrate as well as ambient air remains ο above 12 C during application and curing of the materials...

Working time of POLFLOOR-PU 807 decreases when ambient temperature rises. Prolonged storage of partially used containers must be avoided as contact with atmospheric moisture will result in skinning and clouding of the product. Do not mix or apply unless surface, air and material temperatures are over 12°C during the next 24 hours. Do not apply to floors if there is moisture in the subfloor drive or hydrostatic pressure. Prior precautions measurements of humidity with special device are suggested. It cannot be applied in thickness for filling cracks or holes. In case of cracks or holes we recommend...