EasyFit ®
2Pages

Johns Manvffle Formaldehyde-free™ Fiber Glass Insulation JM FORMALDEHYDE-FREE " FIBER GLASS INSULATION JM Formaldehyde-free™ fiber glass building insulation offers superior thermal and acoustical performance—and it improves indoor air quality, because it's made without formaldehyde. Why is that important? Because the U.S. Environmental Protection Agency (EPA) recommends limiting exposure to formaldehyde as much as possible, and the California Air Resources Board, a division of the California EPA, recommends that homeowners, builders and architects use building materials and insulation made without formaldehyde when building a home or remodeling. JM is the only company in the industry with a complete line of Formaldehyde-free™ fiber glass building insulation. Visit JM.com/formfree PRODUCT DESCRIPTION Johns Manville EasyFit® perforated thermal and acoustical fiber glass insulation features vertical perforations that allow installers to separate sections by hand, rather than cutting the insulation, to fit nonstandard-width framing cavities quickly and easily. Considering that over 35 percent of all cavities in a typical home are nonstandard-width (even more in custom construction), EasyFit insulation allows contractors and installers to significantly increase their installation productivity. The lightweight thermal and acoustical insulation is made of long, resilient glass fibers bonded with an acrylic thermosetting binder AVAILABLE FORMS • Unfaced batts • Kraft-faced batts (where vapor control is required) Each EasyFit package contains both standard and perforated batts to meet all your insulating needs. Use to speed installation in nonstandard-width cavities, anywhere unfaced or kraft-faced insulation • Wood frame construction - residential homes and light commercial buildings • Interior wall sound control - interior walls and floor and ceiling assemblies (For sound class ratings for wall assemblies, see the appropriate STC values datasheet for either steel or wood framing.) • Basement wall insulation Vertical perforations allow batts to be separated to fit nonstandard-width cavities, for faster, easier installation. It installs by simply pressing in place between studs. Fasteners may also be used with kraft-faced insulation. The kraft facing on this product will burn, and must not be left exposed. It must be covered with gypsum board or another approved interior finish. Where an exposed application is required, use FSK-25 flame-resistant faced insulation Slit Configuration Note: In colder climate areas, vapor retarders (whether attached to the insulation or applied separately) are often placed toward the heated or conditioned side of the wall This is done to reduce water vapor penetration into the wall from the building interior. Conversely, in predominantly hot, humid climates local practices often call for placing the vapor retarder toward the outside of the wall cavity. Check your local building codes forvapor retarder requirements. Formaldehyde-free'" Perforated Thermal and Acoustical Fiber Glass Insulation PERFORMANCE ADVANTAGES • Improves indoor air quality- because it's made without formaldehyde. • Thermally efficient - provides effective resistance to heat transfer with R-values • Controls moisture - kraft facing resists water vapor transmission • Controls sound - reduces transmission of conversations and equipment noises through nterior and exterior walls and floor and ceiling assemblies. • Noncorrosive - does not accelerate corrosion of pipes, wiring or metal studs. • Durable - unaffected by moisture, oil, grease and most acids. It will not rot, mildew or otherwise deteriorate. • Resilient - bonded glass fibers will not pull apart during normal applications and resist settling, breakdown and sagging from vibration • Flexible - forms readily around corners and curved surfaces.

EasyFit ® Visit us at JM.com Or call: 1-800-654-3103 Formaldehyde-free ™ Perforated Thermal and Acoustical Fiber Glass Insulation building code Compliance and Fire Hazard Classification ICBO SBCCI BOCA IBC/IRC Flame Spread* Smoke Developed* EasyFit Unfaced batts EasyFit Kraft-faced batts All Types Types III, IV, V All Types Types III, V, VI All Types Types III, IV, V All Types/All Types Types III, IV, V/All Types 25 Not Rated 50 Not Rated * Per ASTM E 84. Available Forms* Facing R-value RSI-value Thickness** Batt Length Typical Perforated Batts Total Batts Coverage (hr• ft² •°F/Btu) (m²...