HZ5™-HardieShingle pg. 60-68
9Pages

60 HardieShingle® Siding Product Description HardieShingle® siding is fiber-cement shingle siding for sidewall applications. HardieShingle® siding is available as straight-edge panels or staggered-edge panels 1.2m (48 in.) long by 406mm (16 in.) high. For smaller coverage areas, individual shingles are also available in 152mm (6 in.), 203mm (8 in.) and 305 (12 in.) widths. Please see your James Hardie® dealer for local availability of these products. HardieShingle® siding is available as a prefinished James Hardie product with ColorPlus® technology. The ColorPlus® coating is a factory applied, oven-baked finish available on a variety of James Hardie siding and trim products. See your local dealer for details and availability of products, colors and accessories. Staggered Edge / Individual shingle Staight Edge / Individual Shingle General Product Information Working Safely General Installation Requirements General Fastener Requirements Finishing and Maintenance HardieTrim® Boards/Battens HardieSoffit® Panels HardiePlank® Lap Siding HardieShingle® Siding HardiePanel® Vertical Siding Appendix/ Glossary Tools for Cutting and Fastening

61 General Product Information Working Safely General Installation Requirements General Fastener Requirements Tools for Cutting and Fastening HardieTrim® Boards/Battens HardieSoffit® Panels HardiePlank® Lap Siding HardieShingle® Siding HardiePanel® Vertical Siding Appendix/ Glossary Finishing and Maintenance Like conventional wood-shingle siding, HardieShingle® siding requires the use of a starter strip and a starter course before installing the first full course of shingle panels or individual shingles. The starter strip sets the initial shingles at the proper angle and the starter course...

62 For HardieShingle® panels start at one end and work across the wall. Measure and trim the first panel to make sure the end of the panel falls over framing. Using the chalk line as a guide along the panel top edge, carefully position the panels and secure with suitable fasteners and spacing for your particular application as noted in the NER-405. Align the bottom edges of the trim and the siding for the best appearance. Where the panel begins at a corner board or at door or window casings, cut the upper portion of the panel back even with the edge of the keyway. Where the siding meets the...

HS0918_P1/6 4/09 WARNING: AVOID BREATHING SILICA DUST James Hardie® products contain respirable crystalline silica, which is known to the State of California to cause cancer and is considered by IARC and NIOSH to be a cause of cancer from some occupational sources. Breathing excessive amounts of respirable silica dust can also cause a disabling and potentially fatal lung disease called silicosis, and has been linked with other diseases. Some studies suggest smoking may increase these risks. During installation or handling: (1) work in outdoor areas with ample ventilation; (2) use fiber...

64 HS0918_P2/6 4/09 position nails into framing through previous courses. Only when application is to minimum 11.1mm (7/16") thick APA rated sheathing, position nails at 349mm (13 3/4") o.c. Allow 9.5 (3/8") from panel edges. second course 3mm (1/8") minimum gap for caulk second course third course first course 8 1/4" or 9 1/4" HardiePlank® siding INSTALLATION Fastener Requirements 2.1mm x 4.7mm HD x 38mm (1.5") long ringshank nails are used for fastening HardieShingle® Staggered Edge Notched Panels to both framing and to 11.1mm (7/16") thick APA rated sheathing. HardieShingle® Staggered...

65 HS0918_P3/6 4/09 Panels for sidewall applications are available in 1.2m (48") lengths. Pieces needed for one square (9.3 sq.m./100 sq.ft.) of product coverage = approximately 45, based on maximum 178mm (7") exposure. HARDIESHINGLE® STRAIGHT EDGE NOTCHED PANEL COVERAGE STRAIGHT EDGE NOTCHED PANELS INSTALLATION Maximum Exposure of 178mm (7") Steps 1 - 4 REFER TO STAGGERED EDGE INSTRUCTIONS ABOVE 8 1/4" HardiePlank® siding position nails into framing through previous courses. Only when application is to minimum 11.1mm (7/16") thick APA rated sheathing, position nails at 349mm (13 3/4") o.c....

66 HS0918_P4/6 4/09 WINDOWS AND DOORS Building wall components such as windows, doors and other exterior wall penetrations shall be installed in accordance with the component manufacturer’s written installation instructions and local building codes. Where windows or doors are installed, continue the application of siding as if the wall is complete. Triming for the opening and using the resulting piece may throw off the spacing above the break. Figure 17 CORNER DETAILS A. Panels butted against corner boards. B. Panels butted against square wood strip on inside corner, flashing behind. C....

67 HS0918_P5/6 4/09 WIND LOAD TABLE Table 1 - Straight Edge Notched Panel applied to a minimum 11.1 mm (7/16”) thick OSB sheathing or equivalent sheathing only. Min. 2.1 mm shank x 4.7 mm HD x 38 mm (1 1/2”) long corrosion resistant siding nail 350 mm (13”) o.c. to notched panels installed with butt edges in alignment Min. 11.1 mm (7/16”) thick APA rated OSB sheathing or equivalent Min. 11.1 mm (7/16”) thick APA rated OSB sheathing or equivalent NA 3.25 kPa 68 psf Min. 2.1 mm shank x 4.7 mm HD x 38 mm (1 1/2”) long corrosion resistant siding nail 350 mm (13”) o.c. to notched panels...

68 Please visit www.jameshardie.com for Additional Product Information and Availability, Installation Information, Warnings, and Warranties © 2009 James Hardie International Finance B.V. All rights reserved. TM, SM, and ® denote trademarks or registered trademarks of James Hardie International Finance B.V. is a registered trademark of James Hardie International Finance B.V. HS0918_P6/6 4/09 RECOGNITION: In accordance with ICC-ES Legacy Report NER-405, HardieShingle® Staggered Edge Notched Panels are recognized as a suitable alternate to that specified in: the BOCA National Building...