*myarchiexpo

Catalogs
James Hardie - France
HZ10™-HardieTrim pg. 40-64

HZ10™-HardieTrim pg. 40-64

Product catalog summary

Product Description:
HardieTrim® boards are decorative, non-load bearing trim products used for various architectural details. They come in three thicknesses (5/4, 4/4, and 7/16 inch) and lengths of 10 to 12 feet, with widths from 4 to 12 inches. They can be finished with PrimePlus® primer or ColorPlus® Technology for a durable finish.

Installation Guidelines:
Pre-assembled corners are recommended for 5/4 boards. Use 2-inch, 16-gauge finish nails, keeping nails at least 1 inch from ends and 3/4 inch from edges. Weather cuts should be at least 22.5° and sloped downward. Ensure proper flashing and maintain a 1/4-inch gap between flashing and siding for band boards.

Fastening Specifications:
Use stainless steel finish nails. For 4-inch and 6-inch boards, use two fasteners every 16 inches; for 8-inch boards, use three fasteners; and for 12-inch boards, use four fasteners. Nails should be spaced no greater than 16 inches apart.

Window and Door Trim:
Install using the "cap over" method with proper flashing. A shim strip may be used to ensure the trim sits flat and parallel with the wall.

Additional Installation Notes:
For fascia and rake board applications, nail over a wood or steel subfascia. Use weather/bevel cuts for longer fascia runs and install a drip edge to protect the fascia board.

Specifications:
HardieTrim Battens are used with HardiePanel vertical siding for a board and batten look. They must be attached to wood or steel backing using approved fasteners. Stainless steel finish nails are recommended.

Installation Procedures:
1. Install battens vertically and parallel using chalk lines or a level.
2. Position fasteners no closer than 3/4” from edges and 1” from ends, with a maximum spacing of 16” on center.
3. Create a weather-cut of at least 22.5° angle for horizontal joints.
4. Use a horizontal band board if installing battens over horizontal panel joints.

General Requirements:
A water-resistive barrier is required. Flashing is necessary over horizontal protruding and exposed trim. Maintain clearances between Hardie products and other structures.

Safety and Handling:
Avoid breathing silica dust by working in well-ventilated areas and using appropriate cutting tools and protective equipment. Store products flat, dry, and covered before installation.

Fastening Requirements:
Use corrosion-resistant, galvanized, or stainless steel fasteners. Drive fasteners perpendicular to siding and framing, ensuring heads fit snugly against siding.

Painting and Caulking:
Use 100% acrylic topcoats and paint within specified timeframes. Use elastomeric or latex joint sealants as per manufacturer instructions.

Warnings:
Avoid bridging floors with HardieTrim Battens and/or HardiePanel Siding. Follow all safety guidelines to prevent exposure to silica dust.

General Fastening Requirements:
Pneumatic fastening is recommended. Set air pressure to ensure fasteners are driven snugly with the siding surface. Use corrosion-resistant fasteners, preferably stainless steel near water bodies.

ColorPlus® Technology Caulking, Touch-Up & Laminate:
Touch up minor damages with ColorPlus® Technology applicators. Caulk non-factory cut edges and use edge coaters for other edges.

Painting James Hardie® Products:
Ensure surfaces are clean and dry before repainting. Use 100% acrylic topcoats and avoid stains or oil-based paints.

Installation Requirements:
Use finish nails for HardieTrim Battens. Ensure adequate fastening and follow clearance details as per local building codes.

Cutting Instructions:
To minimize silica dust exposure, use outdoor cutting stations with dust-reducing tools and HEPA vacuums.

Storage & Handling:
Store products flat, dry, and covered. Avoid installing wet or saturated siding to prevent shrinkage.

Clearance and Flashing Requirements:
Maintain specified clearances between siding and other structures. Use flashing over horizontal protrusions and ensure proper drainage away from the building.

Recognition:
HardieTrim® Battens are recognized as an alternative to conventional trim in various building codes.

Specifications and Procedures:
Maintain a minimum clearance of 1-2 inches between trim products and decks, paths, steps, and driveways. Use step flashing for roof intersections with sidewalls.

Trim Application:
Use weather cuts sloped away from the wall for corners or vertical trim. Trim openings for windows and doors before siding installation.

Fastening and Painting:
Use corrosion-resistant fasteners. Paint within 180 days for primed products and 90 days for unprimed.

Caulking and Touch-Up:
Use elastomeric or latex joint sealants complying with ASTM standards. For ColorPlus® Technology products, ensure surfaces are clean and dry before repainting.

Recognition and Compliance:
HardieTrim boards are recognized as an alternative to conventional trim in various building codes.

Catalog excerpts

40 HardieTrim® Boards Products Description HARDIETRIM® 5/4 BOARDS HardieTrim 5/4 boards is a decorative non-load bearing trim product. HardieTrim 5/4 boards is 1-in. thick and comes in 10-ft. and 12-ft. lengths, based on product availability. In addition to frieze, fascia, rake, window, door, and corner details, HardieTrim 5/4 boards may be used to construct light blocks, column wraps and decorative scroll work. Available in commonly-used nominal widths from 4 in. to 12 in., HardieTrim 5/4 boards comes finished with either with the PrimePlus® factory primer and sealer or with ColorPlus® Technology. The ColorPlus coating is a factory-applied, oven-baked finish available on a variety of James Hardie® siding and trim products. See your local dealer for details and availability of products, colors and accessories. HARDIETRIM® 4/4 BOARDS HardieTrim 4/4 boards is a decorative non-load bearing trim product. HardieTrim 4/4 boards is 3/4-in. thick and comes in 10-ft and 12-ft. lengths. HardieTrim 4/4 boards may be used for frieze, fascia, rake, window, door, and corner details where the look of a 3/4-in. product is desired. HardieTrim 4/4 boards is available in commonly-used nominal widths from 4 in. to 12 in. See your local dealer for details and availability of products and accessories. HARDIETRIM® 7/16” BOARDS HardieTrim 7/16” boards is a decorative non-load bearing trim product. HardieTrim 7/16” boards is 7/16-in. thick and comes in 12-ft. lengths. HardieTrim 7/16” boards may be used for frieze, fascia, rake, window, door, and corner details where a 7/16-in. product is desired. HardieTrim 7/16” boards is available in commonly used nominal widths from 4 in. to 12 in. See your local dealer for details and availability of products and accessories HARDIETRIM® BATTENS HardieTrim Battens are a decorative, non-load bearing trim product. HardieTrim Battens are 3/4” thick, 2 1/2” wide, and come in 12’ lengths. See your local dealer for details and availability of product colors and accessories. Smooth HardieTrim 5/4, 4/4, 7/16” Boards Select Cedarmill© HardieTrim 7/16” Boards Rustic HardieTrim 5/4, 4/4 Boards ColorPlus TIP: HardieTrim 4/4, 5/4, 7/16 boards with ColorPlus Technology is shipped with a protective laminate slip sheet. James Hardie recommends keeping the protective sheet in place during cutting and fastening to reduce damage to the boards. Remove the protective sheet only after installing the boards and filling the nail holes with a colored touch-up pen. HardieTrim Batten board - Rustic and smooth Left: HardieTrim Batten board – Smooth with HardiePanel® Vertical Siding for Board & Batten look. Below: A Complete James Hardie Exterior – Close-up on trim products. General Product Information Working Safely Tools for Cutting and Fastening General Installation Requirements General Fastener Requirements Finishing and HardieTrim® Maintenance Boards/Battens HardieWrap® Weather Barrier HardieSoffit® Panels HardiePlank® Lap Siding HardieShingle® Siding HardiePanel® Vertical Siding NER -405 Legacy Report Appendix/ Glossary

Open the catalog to page 1

41 General Product Information Tools for Cutting and Fastening General Installation Requirements General Fastener Requirements Finishing and Maintenance HardieTrim® Boards/Battens HardieWrap® Weather Barrier HardieSoffit® Panels HardiePlank® Lap Siding HardieShingle® Siding HardiePanel® Vertical Siding NER -405 Legacy Report Appendix/ Glossary Working Safely Installation of HardieTrim® 5/4 boards Double board outside corners TIP: When pre-assembling exterior corners using HardieTrim 5/4 boards, position the finish nailer parallel with the trim Single board inside corners Inside corners can be...

Open the catalog to page 2

42 A Band board is a decorative horizontal trim used to break up the field of siding on a building. Any width of HardieTrim® 5/4 boards can be used for band board depending on the type of detail desired. If installing a band board, pay special attention to flashing details and allow for potential shrinkage of solid rim joists in the walls that the band board may be attached to. Caulk between the underside of the band board and the siding below. Do not caulk between the flashing and siding above the band board, and maintain a 1/4-in. gap between the two. Also make sure that the water-resistive...

Open the catalog to page 3

43 General Product Information Tools for Cutting and Fastening General Installation Requirements General Fastener Requirements Finishing and Maintenance HardieTrim® Boards/Battens HardieWrap® Weather Barrier HardieSoffit® Panels HardiePlank® Lap Siding HardieShingle® Siding HardiePanel® Vertical Siding NER -405 Legacy Report Appendix/ Glossary Working Safely Window and doo r trim 1/4 in. gap Water-resistive barrier 1/8-in. caulked gap is left between siding and the side trim pieces. Header piece spans the window including the side trim pieces. Side trim pieces go to the top of the window. Bottom...

Open the catalog to page 4

44 HardieTrim® 4/4, 7/16 boards may be used for both inside and outside corners, door and window trim, as well as band board and other trim details on a house. For fasteners recommended for specific applications, see the chart on pg. 29. Installation of HardieTrim® 4/4, 7/16 Boards General Product Information Working Safely Tools for Cutting and Fastening General Installation Requirements General Fastener Requirements Finishing and HardieTrim® Maintenance Boards/Battens HardieWrap® Weather Barrier HardieSoffit® Panels HardiePlank® Lap Siding HardieShingle® Siding HardiePanel® Vertical Siding...

Open the catalog to page 5

45 General Product Information Tools for Cutting and Fastening General Installation Requirements General Fastener Requirements Finishing and Maintenance HardieTrim® Boards/Battens HardieWrap® Weather Barrier HardieSoffit® Panels HardiePlank® Lap Siding HardieShingle® Siding HardiePanel® Vertical Siding NER -405 Legacy Report Appendix/ Glossary Working Safely drip edge After the fascia is installed, a vinyl, coated aluminum or galvanized drip-edge flashing must be installed to the roof sheathing overlapping the fascia board. The drip edge helps protect the top edge of the fascia board and it minimizes...

Open the catalog to page 6

All James Hardie - France catalogs and technical brochures

Archived catalogs

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.

Brand list