1. Catalogs
  2. JACUZZI
  3. Owner’s Manual ONE-PUMP (PU1) & TWO-PUMP (PU2)
video corpo
cad

Owner’s Manual ONE-PUMP (PU1) & TWO-PUMP (PU2)

Owner’s Manual ONE-PUMP (PU1) & TWO-PUMP (PU2)
1 / 31 PagesView full catalog

Owner’s Manual ONE-PUMP (PU1) & TWO-PUMP (PU2)

Product catalog summary
Owner's Information
This section provides spaces for recording dealer and installer information, as well as details about the spa model, serial number, color, and delivery date. It advises locating the model and serial numbers on a white plate near the access panel.
Table of Contents
The manual includes sections on safety instructions, electrical mode selection, spa cover installation, filling and draining the spa, electrician instructions for different models, system operation, display messages, maintenance tasks, water chemistry, and troubleshooting.
Important Safety Instructions
This section emphasizes the importance of following safety precautions when using the spa. Key points include supervision of children, proper electrical grounding, installation guidelines, water temperature recommendations, warnings against substance use, and maintenance of water chemistry.
Selecting Electrical Mode and Location
Guidance is provided on choosing between 120-volt and 240-volt electrical modes for one-pump models, with implications for heater operation and installation requirements. Certified electricians are required for two-pump models.
Installation Requirements
The spa must be placed on a solid, flat, and level surface with a minimum load-bearing capacity of 160 pounds per square foot. Avoid placing the spa under overhead electrical lines and ensure adequate access to service panels.
Spa Cover Installation
Proper installation of the spa cover is crucial to avoid drowning risks. The cover should be secured with latches and removed completely before spa use.
Filling and Draining the Spa
Fill the spa with cold water 6 to 8 inches below the top edge to avoid overfilling. Regular draining is necessary to remove dissolved solids and protect equipment.
Electrical Requirements
For two-pump models, a 240VAC, 60HZ, 50A, Class A GFCI-protected service is required. Installations must comply with the National Electrical Code and local codes.
System Operation
The spa performs a self-diagnostic test upon start-up. Temperature can be adjusted between 80°F and 104°F. The pump and LED light have adjustable settings.
Lighting Modes
The spa features multiple lighting modes, including a color wheel and various static colors. The light will automatically turn off after four hours if left on.
Spa Water Maintenance
Users can program water filtration times ranging from 1 to 8 hours every 12 hours. Continuous filtration is also an option.
Spa Heating Modes
The spa is factory set to Standard Heating Mode. Users can switch to Economy Mode or Sleep Mode for energy efficiency.
Temperature Adjustment
The spa's temperature can be adjusted between 80°F and 104°F using the control panel.
Jets Operation
The spa features two jet pumps with adjustable flow settings.
Display Messages
The spa provides various display messages indicating conditions like overheat, potential freeze, sensor issues, and low flow problems.
Filter Maintenance
Regular cleaning or replacement of the filter cartridge is necessary to maintain performance.
Water Chemistry
Proper water chemistry is crucial for equipment safety and water appearance. Key factors include pH, total alkalinity, calcium hardness, temperature, and total dissolved solids.
Water Chemistry and Maintenance
Maintaining proper water chemistry is crucial for spa safety and longevity. Key parameters include pH level, alkalinity, sanitizer levels, and shock treatment.
Maintenance Schedule
Regular testing and adjustments are necessary to prevent damage and ensure sanitary conditions. A schedule is provided for daily, weekly, and bi-weekly maintenance tasks.
Equipment Maintenance
Includes LED light replacement, headrest installation, and freeze protection measures.
Cleaning and Care
Use soft liquid cleaners for the spa and maintain the Weather Shield cover by washing with mild soap and water.
Troubleshooting
Common issues include no heat, jets not working, and low water flow. Solutions involve checking power, cleaning filters, and ensuring proper water levels.
Ozone System
The spa may include an ozone generator, which acts as a secondary sanitizer.
See more

Catalog excerpts

Owner’s Manual ONE-PUMP (PU1) & TWO-PUMP (PU2)-2

OWNER’S INFORMATION DEALER Company ___________________________________________________________________ Address ___________________________________________________________________ Phone ___________________________________________________________________ E-mail ___________________________________________________________________ INSTALLER Company ___________________________________________________________________ Address ___________________________________________________________________ Phone ___________________________________________________________________ SPA Model (see below) ______________________________________________________________...

 Open the catalog to page 2
Owner’s Manual ONE-PUMP (PU1) & TWO-PUMP (PU2)-3

TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS…………………………………………………………………………..………….4-5 SELECTING ELECTRICAL MODE AND A LOCATION…………………………………………………………………..6 SPA COVER INSTALLATION……………………………………………………………………………………………………..7 FILLING YOUR SPA……………………………………………………………………….…………………………………………8 DRAINING YOUR SPA……………………………………………………..…………….………………………..………………8 FOR THE ELECTRICIAN, TWO-PUMP, PU2 MODELS……………………………………………………..…………9-11 FOR THE ELECTRICIAN, ONE-PUMP, PU1, MODELS, CONVERT HEATER TO 240VOLT……….…….12-14 SYSTEM OPERATION ONE-PUMP, PU1 MODELS…………………………………………………………………….15-16 SYSTEM OPERATION TWO-PUMP, PU2...

 Open the catalog to page 3
Owner’s Manual ONE-PUMP (PU1) & TWO-PUMP (PU2)-4

Important Safety Instructions When installing and using this electrical equipment, basic safety precautions should always be followed, including the following: READ AND FOLLOW ALL INSTRUCTIONS 1. 2. WARNING: To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times. WARNING: A wire connector is provided on this unit to connect a minimum 6 AWG (4.11 mm) solid copper conductor between this unit and any metal equipment, metal enclosures of electrical equipment, metal water pipe, or conduit within 5 feet (1.5m) of the unit. 3. DANGER...

 Open the catalog to page 4
Owner’s Manual ONE-PUMP (PU1) & TWO-PUMP (PU2)-5

12. Caution: Maintain water chemistry in accordance to manufacturer’s instructions. Your spa can be a source of great pleasure. It offers healthful stimulating recreation and is a delightful fun center for you, your family and friends. However, it contains large quantities of water and is deep enough to present inherent dangers to life and health unless the following safety rules are strictly observed. 13. Never permit the spa to be used unless it is attended by at least one person other than the bather. Someone should be present to lend assistance if the bather should be in trouble due to injuries,...

 Open the catalog to page 5
Owner’s Manual ONE-PUMP (PU1) & TWO-PUMP (PU2)-6

Selecting electrical mode and a location ❑ WARNING! DO NOT STORE SPAS OUTDOORS WITHOUT PROPER WATER LEVEL. A spa stored outside in direct sun, without proper water level, uncovered or under a tarp/cover, can accumulated temperatures that will damage the spa, its components and void the warranty. Only store an empty spa indoors or in the shade. One-pump (PU1) models ❑ Will you operate the spa on 120- or 240-volts heater? Your spa comes ready to plug into a standard 120 volt / 15-amp outlet for power. However, the heater can be converted from 120-volt 1000 watts, to 240 volt 4000 watts, with a...

 Open the catalog to page 6
Owner’s Manual ONE-PUMP (PU1) & TWO-PUMP (PU2)-7

WARNING! AVOID DROWNING RISK • Failure to follow instructions may result in injury or drowning. • Non-secured covers are a hazard. • Keep children away. People or objects cannot be seen under the cover. • Because of entrapment possibility, remove cover completely before entry of bathers. • Excess weight can break the insulating foam, bend the steel reinforcement and damage the cover. Do not allow people or pets to stand or sit on the cover. Do not allow loads such as snow, leaves or anything else to accumulate on the cover. Do not use the cover as a table. Caution, to avoid damage to the cover...

 Open the catalog to page 7
Owner’s Manual ONE-PUMP (PU1) & TWO-PUMP (PU2)-8

Filling Your Spa Warning! Your spa is constructed of a very resilient and flexible polymeric material. It is designed to flex as much as 2 inches (5cm) without damage. However, overfilling the spa and/or installing on a non-level surface for extended periods of time can permanently distort the original shape of your spa, cause structural damage, effect the sealing of the cover and void your warranty. Remove the access panel and ensure the drain valve is closed and the cap is secure (Fig 5). Place a garden hose into filter area (Fig 7) and fill the spa with cold (never warm or hot) water 6 to...

 Open the catalog to page 8
Owner’s Manual ONE-PUMP (PU1) & TWO-PUMP (PU2)-9

Two-pump (PU2) models, FOR THE ELECTRICIAN Installations that do not adhere to these instructions can expose users to electric shock and will void the warranty. Power Requiremnts 240VAC, 60HZ, 50A, Class A GFCI-protected service (Circuit Breaker rating 50A). 4 wires (hot, hot, nuetral, ground). GFCI PROTECTION: The new service must be protected with by a GFCI and a disconnect switch. The National Electrical Code requires that spas connected to 240 volts circuits be equipped with a GFCI and disconnect switch. See National Electric Code Articles 680-12 and 680-42. This spa is not equipped with...

 Open the catalog to page 9
*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.