Owner’s Manual Jacuzzi® Full Spectrum Infrared Saunas Please read this manual before using your Sauna for the first time. Please keep this manual for future reference.

Installation- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 04 01 | Jacuzzi® JS-1i and JS-2i- - - - - - - - - - - - - - - - - - - - - - - - - - - - 05 Packaging - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 06 Assembly Instructions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 07 02 | Jacuzzi® JS-3i- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 20 Packaging - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 21 Assembly Instructions - - - - - - - - - -...

Installation Choosing a Location Place your sauna on a dry and level surface for best results. Installation requirements for your sauna are as follows: 1. Your Jacuzzi® sauna is a self-contained and freestanding unit. It should not be built into any structure without prior authorization. 2. Please maintain a minimum of 4-inch clearance on all sides of the unit to allow air to circulate while giving access for the power cord. Cleaning and Maintenance 1. Before using your sauna for the first time, clean the inside of the sauna with a damp cloth. 2. Place a towel on the floor and bench to absorb...

Jacuzzi® Saunas JS-1i and JS-2i Packaging - - - - - - - - - - - - - - - - - - - - - - - - 06 Assembly Instructions - - - - - - - - - - - - - - - - - - 07

Packaging Contents of Boxes . Box 1 of 6 Roof and Floor Panels Left Side Wall Front Wall Metal Threaded Rods Installation Manual Right Side Wall Back Wall 2 x Full Spectrum Heaters Right Side Wall Door Handle Front Heater Mounting Screws (4 sets) Wood piece (2 pieces)

Assembly Instructions Assembly of the sauna requires a minimum of two adults to complete. As noted, a third person is recommended when installing the glass components. Please read the instructions thoroughly before and during assembly to ensure proper installation of the unit. Wearing booties to cover your shoes will protect the wood from getting scuffed or stained. 1 - Location of Sauna and Installation Order When determining a location for your sauna, please keep in mind the following: 1. The main power cord on the sauna must be easily accessible. 2. The location must be dry and level. 3. Panels...

Assembly Instructions Cont’d 4 - Connecting Side Walls 1. Place the left side wall in the slot in the floor positioned as in the drawing below. 2. When the wall is in place, make sure the metal rod is positioned in the metal nut in the floor. 3. Screw the metal bolt from the top of the panel into the metal nut in the floor using your hand to twist the metal rod. 4. Repeat this step installing the Right Side Wall. If the panels still seem too tight to come down all the way, try backing off the bracket screws by one half turn with a Phillips head screwdriver. Left Side Wall Installed Right Side...

Assembly Instructions Cont’d 5 - Installing Side Wall Glass When installing the glass panels, a third person is recommended to support the glass during installation.. 1. Insert the left side wall glass into the slot in the left side wall and make sure it’s well seated on the floor. 2. Repeat this step with the Right Side glass.

Assembly Instructions Cont’d 6 - Install Front Columns 1. Located the two (2) front columns and the corresponding metal rods. 3. Align one of the threaded columns with the left side glass and position the metal rod over the metal nut in the floor. 4 Hand screw the metal rod into the nut until it is tight. 5. Repeat this step for the Right Side Column. 2. Thread the rods through the columns. Note: Some of the rod will be exposed at the top of the column.

Assembly Instructions Cont’d 7 - Installing Under Bench Support Slide down the bench heater panel by lining up its sides with the vertical guides on the left and right side wall panel. 1. Be careful not to scratch the side panels when positioning the heater panel. 2. Push the bench heater panel all the way down until it is touching the floor panel and securely in place. Heater must be facing outward Vertical bench heater panel guides are found on the side panels.

Assembly Instructions Cont’d 8 - Connect Heater Connection Under Bench 1. Locate the power supply on the left side wall. 2. The outlets in the power supply are numbered. Match the six (6) numbered black IEC plugs with the numbered outlets and plug them in. Make sure they are well seated. 3. Plug the cable with the Blue/Red/Green wires and molex connector into the receptacle in the power supply. 4. Locate the wood power supply guard. 5. Place it over the power supply and screw it in place.

Assembly Instructions Cont’d 9 - Installing the Bench Install the bench panel by sliding it over the horizontal bench guides on the side panels. Be careful not to scratch the adjacent panels when sliding in the bench. Push the bench all the way in until it touches the back panel and is securely in place. Be sure that the bench is pushed all the way back until it slides under the heater guard to secure the bench in place. After the bench is installed, slide in the included wood pieces to prevent the bench from sliding left to right. One piece can be placed on each side next to the bench.

Assembly Instructions Cont’d 10 - Installing the Roof 1. Locate the roof. 2. Lift the roof over the exposed metal rods and align the holes in the roof over the metal rods. 3. Lower the roof down onto the walls and front columns. 11 - Attach Jacuzzi® Back Wall Sign

Assembly Instructions Cont’d 11 - Installing Left and Right Side Glass Window 1. Locate the Left Front Glass. 2. Lift up the roof an inch and position the left front glass in place sliding it into the left front column. 3. Seat the roof on the glass making sure the glass is in the slot in the roof. 4. Repeat this step for the Right Front Glass.