Catalog excerpts
Technical Datasheet Technical data 1. Properties of the Form: Color: Density (A+B): Mixing ratio Viscosity: Pass (no blistering, cracking or flaking) ISOFLEX-PU 550 is a two-component, solvent-free, polyurethane, liquid waterproofing membrane. • Based on hydrophobic polyurethane resins, it features excellent mechanical, chemical and thermal resistance. • Forms a continuous, elastic, waterproof, vapor-permeable layer, without seams or joints. • Has excellent adhesion to various substrates, such as concrete, cement screeds, wood and most waterproofing membranes. • Applicable even on irregular substrates. Ideal for indoor use (e.g. waterproofing under tiles), as it is solvent-free and almost odorless. Certified as material suitable for contact with potable water, according to the requirements of RD140/2003 (Spanish Regulation that establishes sanitary criteria for water intended for human consumption, in accordance with 80/778/EEC)”. Certified according to EN 1504-2 and classified as a coating for surface protection of concrete. CE marked. ISOFLEX-PU 550 is suitable for waterproofing: • Under tiles in kitchens, bathrooms, balconies, roofs and flat roofs, as long as quartz sand has been previously broadcast on its last layer. • Under thermal insulation boards on flat roofs. • In construction works, highways, tunnels, waterproofing bridge decks, etc. • Aboveground and underground concrete tanks with potable water, metal tanks, fire protection tanks, etc. product in liquid form polyurethane prepolymer grey 1.35 kg/l 100:25 by weight 5,500 mPa-s (at +230C) 2. Properties of the cured membrane Elongation at break: 70% (ASTM D412) Hardness according to SHORE A: 80 ± 2 (EN ISO 7783-2, vapor-permeable Class I, Sd < 5 m) Adhesion: 3.0 N/mm2 Reaction to fire: Euroclass F
Open the catalog to page 1
1. Substrate preparation In general, the substrate must be dry (moisture content < 4%) and free of grease, loose particles, dust, etc. 1.1 Concrete surfaces Any existing cavities in concrete should be repaired in advance. Severe cracks on the substrate must be locally primed and must be sealed with the polyurethane sealants FLEX PU-30 S or FLEX PU-50 S. Concrete and other porous surfaces with a moisture content < 4% should be treated with the epoxy primer DUROFLOOR-PSF, at a consumption of approx. 200-300 g/m2. Application of IsOfLEX-PU 550 should follow within the next 24-48...
Open the catalog to page 2
In that case, as soon as the primer has dried, the first layer of ISOFLEX-PU 550 is applied along the cracks and, while still fresh, the 10 cm wide polyester fleece strip is embedded lengthwise. Then, two extra layers of ISOFLEX-PU 550 are applied over the entire surface. Consumption: approximately 1.0-1.5 kg/m2, depending on the substrate. In case of dense, multiple cracks all over the surface, it is strongly recommended to fully reinforce ISOFLEX-PU 550 membrane with 100 cm wide strips of polyester fleece (60 g/m2). These strips must overlap by 5-10 cm. In that case, as soon as the...
Open the catalog to page 3
Volatile Organic Compounds (VOCs) According to Directive 2004/42/CE (Annex II, table A), the maximum allowed VOC content for the product subcategory j, type SB is 500 g/l (2010) for the ready-to-use product. The ready-to-use product ISOFLEX-PU 550 contains a maximum of 500 g/l VOC. C€ ISOMAT S.A. 17th km Thessaloniki - Ag. Athanasios P.O. BOX 1043, 570 03 Ag. Athanasios, Greece 14 EN 1504-2 DoP No.: ISOFLEX-PU 550/1835-01 Surface protection products Coating CO2 permeability: Sd > 50 m Water vapor permeability: Class I (permeable) Capillary absorption: w < 0.1 kg/m2-h°-5 Adhesion: > 0.8...
Open the catalog to page 4All ISOMAT S.A. catalogs and technical brochures
-
FIBERGLASS FLEECE GF 50 TR1 Pages
-
ISOMAT AK-60 PU2 Pages
-
ACCELERATOR 50002 Pages
-
MICROCEMENT COATINGS BROCHURE32 Pages
-
ISOMAT PU-SYSTEMS BROCHURE20 Pages
-
ISOFLEX-PU 650 BROCHURE8 Pages
-
Technical Datasheet VS-W1 Pages
-
Technical Datasheet SM-161 Pages
