Website:
ISOMAT S.A.
Catalog excerpts
Technical Datasheet 2-component epoxy resin cementitious powder white, grey 1.11 ± 0.02 kg/l 1.00 ± 0.02 kg/l 1.02 ± 0.05 kg/l Description DUROCRET-DECO EPOXY is a three-component, cement-epoxy product, suitable for both indoor and outdoor applications on floors and walls. Advantages: • Excellent abrasion and mechanical resistance. • Resistance to household chemicals. • Very strong adhesion to the substrate. • Very good workability. • Smooth final surface. • Exceptional aesthetic result. • No need for reinforcement with enhancing resins. Certified according to EN 13813 and classified as a CT-C50-F10-AR0.5 floor coating material. DUROCRET-DECO EPOXY is used in a large number of indoor and outdoor applications, such as stairs, floors, walls, swimming pools in residential and public applications. Suitable for high traffic surfaces in commercial shops, exhibition centers, shopping malls, restaurants, hotels, etc., as well as special structures, such as built-in furniture, sanitary ware (washbasins, showers, etc.). Selected for its highly aesthetic design in various applications (e.g. Cycladic architecture). Chemical base (A+B): Chemical base (C): Color (A+B+C): Density of component A: Density of component B: Bulk density of component C: Bulk density (A+B+C): Mixing ratio (A:B:C): Pot life: Minimum hardening temperature: Coating: Final strength: Compressive strength: (EN 13892-2) Flexural strength: (EN 13892-2) Abrasion resistance: (EN 13892-4, BCA) Adhesion strength: Capillary water absorption: (EN 13057) Maximum application thickness Reaction to fire: 1. Substrate preparation The substrate must be free from dust, grease, loose materials, etc. Any defects in the substrate, such as cracks, cavities, etc., must be repaired with suitable materials. Absorbent surfaces, such as concrete, concrete mortar, plaster, gypsum board, are previously primed with FLEX-PRIMER. Nonabsorbent surfaces, such as old tile layers or mosaic, are previously primed with ISOMAT SUPERGRUND. Alternatively, the two-component, water-based epoxy primer EPOXYPRIMER-500 may be used.
Open the catalog to page 1
2. Mixing of DUROCRET-DECO EPOXY Components A, B and C are packaged in a predetermined mixing ratio. Vigorously shake the pot containing component A and then add to the original 32 l packaging. Then, pour all of component B into component A. Mix the two components for about 30'' using a low speed mixer (300 rpm). Make sure to properly reach the walls and bottom of the container while stirring, in order to obtain a homogeneous mixture. Finally, add component C and keep stirring with a low speed mixer for approximately 3 minutes. Do not add water. 3. Application of DUROCRET-DECO EPOXY Apply...
Open the catalog to page 2
Remarks • Temperature during application: +5°C to +30°C. • Due to cement content, the product reacts with water, forming an alkaline solution. Classified as irritant. • Please consult the safety instructions written on the packaging before use. • The processing time of epoxy systems is reduced as temperature increases. Volatile Organic Compounds (VOCs) According to Directive 2004/42/CE (Annex II, table A), the maximum allowed VOC content for the product subcategory l, type WB is 200 g/l (2010) for the ready-to-use product. The ready-to-use product DUROCRET DECO EPOXY contains a maximum of...
Open the catalog to page 3All ISOMAT S.A. catalogs and technical brochures
-
FIBERGLASS FLEECE GF 50 TR1 Pages
-
ISOMAT AK-60 PU2 Pages
-
ACCELERATOR 50002 Pages
-
MICROCEMENT COATINGS BROCHURE32 Pages
-
ISOMAT PU-SYSTEMS BROCHURE20 Pages
-
ISOFLEX-PU 650 BROCHURE8 Pages
-
Technical Datasheet VS-W1 Pages
-
Technical Datasheet SM-161 Pages
