Isolgomma - UPGREI

Product catalog summary

Technical Specifications:
The document provides technical specifications for an acoustic insulation product, specifically designed for floating floors. The product is an 8 mm-thick acoustic insulation roll made of EPDM rubber granules anchored with a carboxylate latex binder to a backing of non-woven, green-colored, anti-stretch film and polyester fiber.

Key Specifications:

Water Vapour Transmission: Sd EN 12086 m 0.075
Fire Grade: EN 13501-1 Efl
Thermal Conductivity: EN 12667 W/m°K 0.047
Thickness Under Load: Various measurements provided under different loads (e.g., 9.1 mm at 2 kPa, 7.5 mm at 50 kPa)
Compression Load: EN 826 kPa 1.75 ± 5%
Dynamic Stiffness: EN 29052/1 MN/m³ 12 ± 1
Superficial Weight: 2.60 kg/m² ± 10%

Acoustic Characteristics:

Acoustic insulation performance is measured with standards such as EN 12354-2 and ASTM E 2179-03, indicating a reduction in sound transmission.

Physical Characteristics:

Roll dimensions: 500 cm length x 104 cm width, including a 4 cm adhesive side border for overlapping during installation.
Backing superficial weight: 80 g/m²

Installation Instructions:

Apply adhesive strip to walls and floors, paying attention to corners.
Install the mat with rubber granules facing down.
Use pre-built adhesive tape to join adjacent mats.
Build the screed and install floor finishing (ceramic or wood).
Trim excess edging strip.

Packaging and Storage:

Each pallet is wrapped in waterproof polythene film. Indoor storage is recommended to prevent moisture exposure.

Additional Notes:

The document states that the technical information provided is based on current knowledge and may be updated without notice.

Catalog excerpts

Floor insulation TECHNICAL DATA Upgrei LineAcoustic insulation for floating floors Technical specification 8 mm-thick acoustic insulation rolls, made of EPDM (Ethylene Propylene Diene Monomer) rubber granules that are anchored with carboxylate latex binder to a backing, made with 80 g/m2 non-woven, green-coloured, anti-stretch film and 200 g/m2 polyester fibre. Each roll is 500 cm lenght x 104 cm width including a 4 cm adhesive side border for rolls overlapping during installation. The total mass surface is 2.60 kg/m2 and the dynamic stiffness (s') is 12 MN/m3. • very high acoustic and thermal performance • extremely easy to lay • resistant to humidity PACKING AND STORING Each pallet is wrapped and protected with waterproof polythene film. Inside storage is recommended to avoid possible wet storing. m Product thickness measured according to norm EN 12431 equal to the value of "Thickness underload dB (50kPa ^ 2 kPa)" ® Measurement executed in deviation from norm EN 29052-1, without applying plaster on the test sample The suggestions and technical information given above represent our knowledge regarding the properties and the product's uses. ISOLGOMMA reserve the right to modify or update this data without prior notice. This document is the property of ISOLGOMMA and all rights are therefore reserved. |S°|GOMMA Isolgomma Srl, Via dell'Artigianato Z.I., 36020 Albettone (VI), tel. 0444790781, fax 0444790784, [email protected], www.isolgomma.com

Open the catalog to page 1

Floor insulation Upgrei Line TECHNICAL DATA Acoustic insulation for floating floors Time (hours) INSTALLATION INSTRUCTIONS Apply the adhesive strip to the wall and Install the acoustic mat with rubber granules Joint two adjacent mats using the pre-built floor with particular attention in the corners facing down adhesive tape and following the dashed lines Install the floor finishing (ceramic or wood) Cut the exceeding part of the edging strip Isolgomma Srl, Via dell'Artigianato Z.I., 36020 Albettone (VI), tel. 0444790781, fax 0444790784, [email protected], www.isolgomma.com

Open the catalog to page 2

Isolgomma - UPGREI

Isolgomma - UPGREI

Catalog excerpts

All Isolgomma catalogs and technical brochures