Decentralised Ventilation

Product catalog summary

Introduction
inVENTer offers decentralised ventilation systems designed to provide fresh and healthy indoor air throughout the year, addressing the lack of natural airflow in modern airtight buildings. Established in 1999, inVENTer focuses on high-quality systems to enhance indoor climate.

System Overview
inVENTer systems cater to various needs, including sound protection, basements, thin walls, and single-room ventilation. These systems are controlled by inVENTer controllers, allowing for individual ventilation zones. The systems consist of paired units installed in outer walls, utilizing Xenion® fans to alternate air direction every 70 seconds, ensuring efficient air exchange.

Energy Efficiency
The systems incorporate ceramic accumulators that store heating or cooling energy, releasing it back into incoming air, thus saving energy and enhancing comfort.

Ventilation Modes

Hot Weather: The system extracts cool stale air, cooling the regenerator, then switches to supply mode, allowing fresh warm air to cool as it passes through the regenerator.
Cold Weather: Warm damp air is extracted, heating the regenerator, then switches to supply mode, where cold dry air is warmed and humidified.

Technical Specifications

iV14-Zero: Wall thickness > 270 mm, air volume flow 8.5 – 29 m³/h, heat recovery 87%, cooling energy recovery 78%.
iV-Smart+: Wall thickness > 270 mm, air volume flow 8.5 – 29 m³/h, heat recovery 87%, cooling energy recovery 78%.
iV-Light: Wall thickness > 290 mm, air volume flow 5 – 21 m³/h, heat recovery 84%, cooling energy recovery 78%.
iV-Compact: Wall thickness > 140 mm, air volume flow 10.5 – 29 m³/h, heat recovery 72%, cooling energy recovery 65%.

Contact Information
inVENTer GmbH, Ortsstraße 4a, D-07751 Löberschütz, Phone: +49 (0) 36427 211-0, Email: [email protected], Web: www.inventer.eu

Version
Document version: 07/2021

Catalog excerpts

Decentralised Ventilation Saving energy all year long

Open the catalog to page 1

Fresh and healthy indoor air all year long Breathing fresh air is essential for health and well-being, but in modern air-tight buildings there is almost no natural flow of fresh healthy air to the inside. Our automatic ventilation systems ensure that stale air from inside is being replaced with fresh oxygen-rich air from the outside, no matter the season of the year. Since we started in 1999, inVENTer ventilation systems have been developed with our know-how and with highest quality in our mind, to meet your needs for the best indoor climate possible. This is how inVENTer works Decentralised...

Open the catalog to page 2

Ventilation when it is hot outside Extract Mode: Cool stale air is extracted from the in- Supply Mode: Fresh warm outside air passes side, cooling the regenerator. through the regenerator and becomes cool due to After 70 seconds the ventilator automatically switches Cool air enters the room and after 70 seconds the ventilator switches to air extract mode again. Ventilation when it is cold outside Exract Mode: Warm damp stale air is extracted from Supply Mode: Fresh, but cold and dry outside air the inside, simultaneously heating up and moisturi- passes through the regenerator, is being humidified...

Open the catalog to page 3

Decentralised Ventilation Systems Technical Data Sound insulation Basic ventilation Especially for thin walls EXHAUST AIR VOLUME FLOW [m³/h] SOUND PRESSURE LEVEL [dB (A)], 2 m HEAT RECOVERY [%] COOLING ENERGY RECOVERY [%] WALL THICKNESS INCL. PLASTER [mm] STANDARD SOUND LEVEL DIFFERENCE [dB] inVENTer GmbH Ortsstraße 4a D-07751 Löberschütz Phone: +49 (0) 36427 211-0 Fax: E-mail: [email protected]

Open the catalog to page 4

Decentralised Ventilation

Decentralised Ventilation

Catalog excerpts

All InVENTer catalogs and technical brochures